Nokia E72 User Guide Issue 4 DECLARATION OF CONFORMITY C E 0434 0 Hereby, NOKIA CORPORATION declares that this RM-530 product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the Declaration of Conformity can be found at http://www.nokia.com/ phones/declaration ofconformity/. ® 2010 Nokia. All rights reserved. Nokia, Nokia Connecting People, Eseries, Nokia E72, and Navi are trademarks or registered trademarks of Nokia Corporation. Nokia tune is a sound mark of Nokia Corporation. Other product and company names mentioned herein may be trademarks or tradenames of their respective owners. Reproduction, transfer, distribution, or storage of part or all of the contents in this document in any form without the prior written permission of Nokia is prohibited. Nokia operates a policy of continuous development. Nokia reserves the right to make changes and improvements to any of the products described in this document without prior notice. ~j ) Java POWERED Java and all Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. This product is licensed under the MPEG-4 Visual Patent Portfolio License (i) for personal and noncommercial use in connection with information which has been encoded in compliance with the MPEG-4 Visual Standard by a consumer engaged in a personal and noncommercial activity and (ii) for use in connection with MPEG-4 video provided by a licensed video provider. No license is granted or shall be implied for any other use. Additional information, including that related to promotional, internal, and commercial uses, may be obtained from MPEG LA, LLC. See http://www.mpegla.com. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, UNDER NO CIRCUMSTANCES SHALL NOKIA OR ANY OF ITS LICENSORS BE RESPONSIBLE FOR ANY LOSS OF DATA OR INCOME OR ANY SPECIAL, INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES HOWSOEVER CAUSED. THE CONTENTS OF THIS DOCUMENT ARE PROVIDED "AS IS". EXCEPT AS REQUIRED BY APPLICABLE LAW, NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITYAND FITNESS FORA PARTICULAR PURPOSE, ARE MADE IN RELATION TO THE ACCURACY, RELIABILITY OR CONTENTS OF THIS DOCUMENT. NOKIA RESERVES THE RIGHT TO REVISE THIS DOCUMENT OR WITHDRAW IT AT ANY TIME WITHOUT PRIOR NOTICE. Reverse engineering of software in the device is prohibited to the extent permitted by applicable law. Insofar as this user guide contains any limitations on Nokia's representations, warranties, damages and liabilities, such limitations shall likewise limit any representations, warranties, damages and liabilities of Nokia's licensors. The third-party applications provided with your device may have been created and may be owned by persons or entities not affiliated with or related to Nokia. Nokia does not own the copyrights or intellectual property rights to the third-party applications. As such, Nokia does not take any responsibility for end-user support, functionality of the applications, or the information in the applications or these materials. Nokia does not provide any warranty for the third-party applications. BY USING THE APPLICATIONS YOU ACKNOWLEDGE THAT THE APPLICATIONS ARE PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW. YOU FURTHER ACKNOWLEDGE THAT NEITHER NOKIA NOR ITS AFFILIATES MAKE ANY REPRESENTATIONS OR WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTIES OF TITLE, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR THAT THE APPLICATIONS WILL NOT INFRINGE ANY THIRD-PARTY PATENTS, COPYRIGHTS, TRADEMARKS, OR OTHER RIGHTS. The availability of particular products and applications and services for these products may vary by region. Please check with your Nokia dealer for details and availability of language options. This device may contain commodities, technology or software subject to export laws and regulations from the US and other countries. Diversion contrary to law is prohibited. FCC/INDUSTRY CANADA NOTICE Your device may cause TV or radio interference (for example, when using a telephone in close proximity to receiving equipment). The FCC or Industry Canada can require you to stop using your telephone if such interference cannot be eliminated. If you require assistance, contact your local service facility. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by Nokia could void the user's authority to operate this equipment. /Issue 4 EN Contents w +, c 0 u Safety 7 About your device 7 Network services 8 About Digital Rights Management 8 Battery removing 9 Find help 10 Support 10 Update device software 10 In-device help 11 Do more with your device 12 Settings 12 Access codes 12 Prolong battery life 13 Free memory 13 Get started 14 Insert the SIM card and battery 14 Insert the memory card 15 Remove the memory card 15 Antenna locations 16 Switch the device on and off 16 Charge the battery 16 Keys and parts 17 Headset 18 Screen saver clock 18 Wrist strap 18 Write text 18 Nokia Switch 19 Nokia Ovi Suite 20 Visit Ovi by Nokia 21 About Ovi Store 21 Your Nokia E72 22 Key features 22 Home screen 22 One-touch keys 23 Optical Navi key 24 Turn to silence calls or alarms 25 Calendar 25 Contacts 26 Multitasking 28 Flashlight 28 Ovi Files 28 Make calls 29 Voice calls 29 Options during a call 29 Voice mail 30 Answer or decline a call 30 Make a conference call 30 Speed dial a phone number 31 Call waiting 31 Call divert. 31 Call barring 32 Voice dialling 32 Make a video call 33 Options during a video call 34 Answer or decline a video call 34 Video sharing 34 Log 37 Messaging 38 Messaging folders 38 Organise messages 39 Nokia Messaging 39 E-mail 39 Message reader 42 Speech 42 Text and multimedia messages 43 Special message types 46 Cell broadcast 46 Messaging settings 47 About Chat 49 Set up Office Communicator 49 Connectivity 50 Data connections and access points 50 Network settings 50 Wireless LAN 51 Active data connections 53 Sync 53 Bluetooth connectivity 54 Data cable 57 PC connections 57 About home network 57 Internet 58 Browse the web 58 Browser toolbar 59 Navigate pages 59 Web feeds and blogs 60 Content search 60 Bookmarks 60 Empty the cache 60 End the connection 61 Connection security 61 Web settings 61 Nokia Office Tools 62 Active notes 62 Calculator 63 File manager 64 Quickoffice 64 Converter 64 Zip manager 65 PDF reader 65 Printing 66 Dictionary 67 Notes 67 Positioning (GPS) 67 About GPS 68 Assisted GPS (A-GPS) 68 Hold your device correctly 69 Tips on creating a GPS connection 69 Position requests 70 Landmarks 70 GPS data 70 Positioning settings 71 Maps 71 Maps overview 72 My position 72 Find places 74 Manage places and routes 75 Share location 77 Drive and Walk 77 H § Maps shortcuts 80 C cu Personalisation 80 C Profiles 81 úSelect ringing tones 82 Customise profiles 82 Personalise the home screen 82 Change the display theme 83 Download a theme 83 Change audio themes 83 3-D ringing tones 84 Media 84 Camera 84 Gallery 87 Photos 88 Share online 93 Music player 96 RealPlayer 98 Recorder 98 Flash player 99 FM radio 99 Nokia Internet Radio 100 Security and data management 102 Lock the device 102 Memory card security 103 Encryption 103 Fixed dialling 104 Certificate manager 104 View and edit security modules 106 Remote configuration 106 Application manager 107 Licenses 109 Sync 110 Mobile VPN 110 Settings 112 General settings 112 Telephone settings 116 Connection settings 117 Application settings 125 Shortcuts 125 General shortcuts 125 Glossary 127 Troubleshooting 130 Green tips 133 Save energy 133 Recycle 133 Product and safety information 133 Index 140 Safety Read these simple guidelines. Not following them may be dangerous or illegal. Read the complete user guide for further information. SWITCH ON SAFE!! Do not switch the device on when wireless phone use is prohibited or when it may cause interference or danger. e ROAD SAFETY COMES FIRST Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. INTERFERENCI All wireless devices may be susceptible to interference, which could affect performance. SWITCH OFF IN RESTRICTED AREAS Follow any restrictions. Switch the device off in aircraft, near medical equipment, fuel, chemicals, or blasting areas. QUALIFIED SERS Only qualified personnel may install or repair this product. ACCESSORIES AND BATTERIES Use only approved accessories and batteries. Do not connect incompatible products. l~ WATER-RESISTANCE Your device is not water-resistant. Keep it dry. About your device The wireless device described in this guide is approved for use on the UMTS 900, 1900, and 2100 MHz networks, and GSM 850, 900, 1800, and 1900 MHz networks. Contact your service provider for more information about networks. Your device supports several connectivity methods and like computers may be exposed to viruses and other harmful content. Exercise caution with messages, connectivity requests, browsing, and downloads. Only install and use services and software from trustworthy sources that offer adequate security and protection, such as applications that are Symbian Signed or have passed the Java VerifiedTM testing. Consider installing antivirus and other security software on your device and any connected computer. Your device may have preinstalled bookmarks and links for third-party Internet sites and may allow you to access third-party sites. These are not affiliated with Nokia, and Nokia does not endorse or assume liability for them. If you access such sites, take precautions for security or content. CilLarning: To use any features in this device, other than the alarm clock, the device must be switched on. Do 7 CI) R tel not switch the device on when wireless device use may cause interference or danger. When using this device, obey all laws and respect local customs, privacy and legitimate rights of others, including copyrights. Copyright protection may prevent some images, music, and other content from being copied, modified, or transferred. Make back-up copies or keep a written record of all important information stored in your device. When connecting to any other device, read its user guide for detailed safety instructions. Do not connect incompatible products. The images in this guide may differ from your device display. Refer to the user guide for other important information about your device. Network service' Your service provider may have requested that certain features be disabled or not activated in your device. If so, these features will not appear on your device menu. Your device may also have customized items such as menu names, menu order, and icons. ADuui DiyiLdI Rights Management When using this device, obey all laws and respect local customs, privacy and legitimate rights of others, including copyrights. Copyright protection may prevent you from copying, modifying, or transferring images, music, and other content. Content owners may use different types of digital rights management (DRM) technologies to protect their intellectual property, including copyrights. This device uses various types of DRM software to access DRM­protected content. With this device you can access content protected with WMDRM 10 and OMA DRM 2.0. If certain DRM software fails to protect the content, content owners may ask that such DRM software's ability to access new DRM­protected content be revoked. Revocation may also prevent renewal of such DRM-protected content already in your device. Revocation of such DRM software does not affect the use of content protected with other types of DRM or the use of non-DRM-protected content. Digital rights management (DRM) protected content comes with an associated licence that defines your rights to use the content. To use the device you must have service from a wireless service provider. Some features are not available on all networks; other features may require that you make specific arrangements with your service provider to use them. Network services involve transmission of data. Check with your service provider for details about fees in your home network and when roaming on other networks. Your service provider can explain what charges will apply. Some networks may have limitations that affect how you can use some features of this device requiring network support such as support for specific technologies 8 like WAP 2.0 protocols (HTTP and SSL) that run on TCP/IP protocols and language-dependent characters. If your device has OMA DRM-protected content, to back up both the licence and the content, use the backup feature a of Nokia Ovi Suite. ß Other transfer methods may not transfer the licences in which need to be restored with the content for you to be able to continue the use of OMA DRM-protected content after the device memory is formatted. You may also need to restore the licence in case the files on your device get corrupted. If your device has WMDRM-protected content, both the licence and the content will be lost if the device memory is formatted. You may also lose the licence and the content if the files on your device get corrupted. Losing the licence or the content may limit your ability to use the same content on your device again. For more information, contact your service provider. Some licences may be connected to a specific SIM card, and the protected content can be accessed only if the SIM card is inserted in the device. Battery removing Switch the device off and disconnect the charger before removing the battery. 9 CL CU ~ ra: Find help Support When you want to learn more about how to use your product or you are unsure how your device should function, go to www.nokia.com/support, or using a mobile device, nokia.mobi/support. You can also select Menu > Applications > Help > Help in your device. If this does not resolve yourissue, do one of the following: Switch off the device, and remove the battery. After about a minute, replace the battery, and switch on the device. Restore the original factory settings. Update your device software. If your issue remains unsolved, contact Nokia for repair options. Go to www.nokia.com/repair. Before sending your device for repair, always back up the data in your device. It is recommended that you back up your personal data before updating your / o o device software. °Warning: If you install a software update, you cannot use the device, even to make emergency calls, until the installation is completed and the device is restarted. Be sure to back up data before accepting installation of an update. Downloading software updates may involve the transmission of large amounts of data (network service). Make sure that the device battery has enough power, or connect the charger before starting the update. After you update your device software or applications, the instructions in the user guide may no longer be up to date. Software updates over the air Select Menu > Ctrl. panel > SW update. Update device software About device software and application updates With device software updates and application updates, you can get new features and enhanced functions for your 10 device. Updating the software may also improve your device performance. ft." With Software update (network service), you can check if there are updates available for your device software or applications, and download them to your device. Downloading software updates may involve the transmission of large amounts of data (network service). Make sure that the device battery has enough power, or connect the charger before starting the update. °Warning: If you install a software update, you cannot use the device, even to make emergency calls, until the installation is completed and the device is restarted. Be sure to back up data before accepting installation of an update. After updating your device software or applications using Software update, the instructions related to the updated applications in the user guide or the helps may no longer be up to date. Select Options and from the following: Start update — Download the available updates. To unmark specific updates that you do not want to download, select the updates from the list. Update via PC — Update your device using a PC. This option replaces the Start update option when updates are only available using the Nokia Software Updater PC application. View details — View information on an update. View update history — View the status of previous updates. Settings — Change the settings, such as the default access point used for downloading updates. Disclaimer — View the Nokia licence agreement. Update software using your PC Nokia Software Updater is a PC application that enables you to update your device software. To update your device software, you need a compatible PC, broadband internet access, and a compatible USB data cable to connect your device to the PC. To get more information and to download the Nokia Software Updater application, go to www.nokia.com/ softwareupdate. In-device help A Your device contains instructions to help to use the applications in your device. To open help texts from the main menu, select Menu > Applications > Help > Help and the application for which you want to read instructions. When an application is open, to access the help text for the current view, select Options > Help. When you are reading the instructions, to change the size of the help text, select Options > Decrease font size or Increase font size. You may find links to related topics at the end of the help text. If you select an underlined word, a short explanation is displayed. Help texts use the following indicators: Link to a related help topic. 5 Link to the application being discussed. When you are reading the instructions, to switch between help texts and the application that is open in the a d s ß C .er 11 CL background, select Options > Show open apps. and the w desired application. Z Do more with your device There are various applications provided by Nokia and third party software developers, that help you do more with your device. To find and download applications, visit the Ovi Store at store.ovi.com. These applications are explained in the guides that are available on the product support pages at www.nokia.com/support or your local Nokia website. ettings Your device normally has MMS, GPRS, streaming, and mobile internet settings automatically configured, based on your network service provider information. You may have settings from your service providers already installed in your device, or you may receive or request the settings from the network service providers as a special message. You can change the general settings in your device, such as language, standby mode, display, and keypad lock settings. Access codes Personal identification number (PIN) code — This code protects your SIM card against unauthorised use. The PIN code (4 - 8 digits) is usually supplied with the SIM card. After three consecutive incorrect PIN code entries, the code is blocked, and you need the PUK code to unblock it. UPIN code — This code may be supplied with the USIM card. The USIM card is an enhanced version of the SIM card and is supported by 3G mobile phones. PIN2 code — This code (4 - 8 digits) is supplied with some SIM cards, and is required to access some functions in your device. Lock code (also known as security code) — The lock code helps you to protect your device against unauthorised use. The preset code is 12345. You can create and change the code, and set the device to request the code. Keep the new code secret and in a safe place separate from your device. If you forget the code and your device is locked, your device will require service. Additional charges may apply, and all the personal data in your device may be deleted. For more information, contact a Nokia Care Point or your device dealer. Personal Unblocking Key (PUK) code and PUK2 code — These codes (8 digits) are required to change a blocked PIN code or PIN2 code, respectively. If the codes are not supplied with the SIM card, contact the network service provider whose SIM card is in your device. UPUK code — This code (8 digits) is required to change a blocked UPIN code. If the code is not supplied with the USIM card, contact the network service provider whose USIM card is in your device. International Mobile Equipment Identity (IMEI) number — This number (15 or 17 digits) is used to identify valid devices on the GSM network. Devices that 12 If you forget any of the access codes, contact your service provider. are, for example, stolen, can be blocked from accessing the network. The IMEI number for your device can be found under the battery. Prolong battery life Many features in your device increase the demand on battery power and reduce the battery lifetime. To save battery power, note the following: Features that use Bluetooth technology, or allowing such features to run in the background while using other features, increase the demand on battery power. Deactivate Bluetooth technology when you do not need it. Features that use wireless LAN (WLAN), or allowing such features to run in the background while using other features, increase the demand on battery power. WLAN on your Nokia device deactivates when you are not trying to connect, not connected to an access point, or not scanning for available networks. To further reduce battery consumption, you can specify that your device does not scan, or scans less often, for available networks in the background. If you have set Packet data connection to When available in connection settings, and thereis no packet data coverage (GPRS), the device periodically tries to establish a packet data connection. To prolong the operating time of your device, select Menu > Ctrl. panel > Settings and Connection > Packet data > Packet data connection > When needed. The Maps application downloads new map information when you scroll to new areas on the map, which increases the demand on battery power. You can prevent the automatic download of new maps. If the signal strength of the cellular network varies much in your area, your device must scan for the available network repeatedly. This increases the demand on battery power. If the network mode is set to dual mode in the network settings, the device searches for the 3G network. You can set the device to use only the GSM network. To use only the GSM network, select Menu > Ctrl. panel > Settings and Phone > Network > Network mode > GSM. The backlight of the display increases the demand on battery power. In the display settings, you can change the length of the time-out period after which the backlight is switched off. Select Menu > Ctrl. panel > Settings and General > Personalisation > Display > Light time-out. To adjust the light sensor that observes lighting conditions and adjusts the display brightness, in the display settings, select Light sensor. To save power, activate the power save mode. Press the power key, and select Activate power saving. To deactivate it, press the power key, and select Deactivate power saving. You may not be able to change the settings of certain applications when the power save mode is activated. Free memory To view how much memory is available for different data types, select Menu > Office > File mgr.. a d Z ß C 15: 13 Get started Many features of the device use memory to store data. The device notifies you if available memory is low. To free memory, transfer data to an alternative memory (if available) or compatible computer. To remove data you no longer need, use File manager or the respective application. You can remove the following: Messages in the folders in Messaging and retrieved e­mail messages from the mailbox Saved web pages Get started Insert the SIM card and battery Safe removal. Always switch the device off and disconnect the charger before removing the battery. 1. Remove the back cover. Contact information Calendar notes Applications shown in Application manager that you do not need Installation files (with .sis or .sisx file extensions) of installed applications. Back up the installation files to a compatible computer. Images and video clips in Photos. 41' v.` 3. Pull out the SIM card holder, and insert the SIM card. Ensure that the contact area on the card is facing down and that the bevelled corner on the card is facing the bevelled corner on the holder. Push the SIM card holder back in. 14 2. Remove the battery, if inserted. Get started 4. Align the battery contacts with the battery compartment connectors, and insert the battery. Incompatible cards may damage the card and the device and corrupt data stored on the card. A memory card may already be inserted in the device. If not, do the following: Insert a compatible memory card in the slot. Ensure that the contact area on the card is facing up and towards the slot. Push the card in. You can hear a click when the card locks into place. vJ : 5. Replace the back cover. Insert the memory card Use only compatible microSD and microSDHC cards approved by Nokia for use with this device. Nokia uses approved industry standards for memory cards, but some brands may not be fully compatible with this device. Remove the memory card °Important: Do not remove the memory card during an operation when the card is being accessed. Doing so may damage the memory card and the device, and corrupt data stored on the card. Before you remove the memory card, press the power key, and select ,__ ...... ., All applications are closed. When Removing memory card will close all open applications. Remove anyway? is displayed, select Yes. Remove memory card and press 'OK' is displayed. 15 Press the memory card to release it from the slot. Get started 5. Pull out the memory card, and close the memory card slot cover. If the device is switched on, select OK. Antenna locations Your device may have internal and external antennas. Avoid touching the antenna area unnecessarily while the antenna is transmitting or receiving. Contact with antennas affects the communication quality and may cause a higher power level during operation and may reduce the battery life. L®J more information, contact a Nokia Care point or your device dealer. To switch off the device, press the power key briefly, and select Switch off!. Charge the battery Your battery has been partially charged at the factory. If the device indicates a low charge, do the following: Connect the charger to a wall outlet. Connect the charger plug to the device. Switch the device on and off To switch on the device: Press and hold the power key. If the device asks for a PIN code or lock code, enter it, and select OK. The preset lock code is 12345. If you forget the code and your device is locked, your device will require 16 service and additional charges may apply. For Ifyou are using a USB charger, connectthe charger plug to the USB connector. When the device indicates a full charge, disconnect the charger from the device, then from the wall outlet. You do not need to charge the battery for a specific length of time, and you can use the device while it is charging. If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or before any calls can be made. Charging with the USB data cable Charging with the USB data cable is slower than charging with the charger. Charging with the USB data cable may Get started not work if you use a USB hub. USB hubs may be incompatible for charging a USB device. When the USB data cable is connected, you can transfer data at the same time as charging. Connect a compatible USB device to your device using a compatible USB data cable. Depending on the type of the device that is used for charging, it may take a while for charging to start. If the device is switched on, select from the available USB modes. Keys and parts 5 — Selection key 6— Call key 7 — Microphone 8 — Keypad 9 — End key 10 — Selection key 11— Light sensor 12 — Secondary camera mom .n.nn.nnnn ..nn~nnnn ~ ~°:: 1-6 — Function key é — Shift key — Sym key Backspace key Enter key Control key nnnnn..nr nnnn.n.nn~ 1— Power key 2 — Headset connector 3 — Earpiece 4 — Optical NaviTM key (scroll key) 17 W rCi t 3 —Volume up key 4 — Voice key W 5 —Volume down key v Note: The surface of this device does not contain nickel in the platings. The surface of this device contains stainless steel. During extended operation such as an active video call and high speed data connection, the device may feel warm. In most cases, this condition is normal. If you suspect the device is not working properly, take it to the nearest authorised service facility. Screen saver clock When the screen saver of your device is activated (the display is black), press the scroll key to see the time and date. Wrist strap Thread the wrist strap, and tighten it. ifA 1— Micro USB connector 2 — Memory card slot Headset You can connect a compatible headset or compatible headphones to your device. You may need to select the cable mode. To make handsfree phone calls, use a headset with a compatible remote control unit, or use the microphone on the device. °Warning: When you use the headset, your ability to hear outside sounds may be affected. Do not use the headset where it can endanger your safety. Write text The input methods provided in the device may vary according to different sales markets. Write text with the keyboard Your device has a full keyboard. To insert punctuation marks, press the corresponding key or a combination of keys. To switch between the different character cases, press the Shift key. 18 Get started To insert digits or characters printed at the top of keys, press and hold the corresponding key, or press and hold the function key and press the corresponding key. To erase a character, press the backspace key. To erase several characters, press and hold the backspace key. To insert characters and symbols that are not shown on the keyboard, press the Sym key. To copy text, press and hold the Shift key, and scroll to highlight the word, phrase, or line of text you want to copy. Press Ctrl + C. To insert the text into a document, move to the correct place, and press Ctrl + V. To change the writing language, or to activate predictive text input, select Options > Input option_ and from the available options. Nokia Switch fl Copy content from your old devir You can use the Switch application to copy content such as phone numbers, addresses, calendar items, and images from your previous compatible Nokia device to your new device. Copy content for the first time To retrieve data from the other device for the first time, on your device, select nu > Ctrl. pane > Switch. Pair the two devices. To have your device search for devices with Bluetooth connectivity, select Continue. Select the device from which you want to transfer content. You are asked to enter a code on your device. Enter a code (1-16 digits), and select . Enter the same code on the other device, and select . The devices are now paired. If your old Nokia device does not have the Switch application, your new device sends it in a message. Open the message in the old device, and follow the instructions on the display. On your device, select the content you want to transfer from the other device. When the transfer has started, you can cancel it and continue later. Content is transferred from the memory of the other device to the corresponding location in your device. The transfer time depends on the amount of data to be transferred. '03 00 19 Get started 20 The type of content that can be transferred depends on the model of the device from which you want to transfer content. If that device supports synchronisation, you can also synchronise data between the devices. Your device notifies you if the other device is not compatible. Synchronise, I etritve, ail Send content Select Menu > Ctrl. panel > Switch. After the first transfer, select from the following to start a new transfer, depending on the model: to synchronise content between your device and the other device, if the other device supports synchronisation. The synchronisation is two-way. If an item is deleted in one device, it is deleted in both. You cannot restore deleted items with synchronisation. lad to retrieve content from the other device to your device. With retrieval, content is transferred from the other device to your device. You may be asked to keep or delete the original content in the other device, depending on the device model. btj to send content from your device to your other device If you cannot send an item, depending on the type of the other device, you can add the item to the Nokia folder, to C:\Nokia or E:\Nokia in your device. When you select the folder to transfer, the items are synchronised in the corresponding folder in the other device, and vice versa. Use shortcuts to repeat a transfer After a data transfer, you can save a shortcut with the transfer settings to the main view to repeat the same transfer later. To edit the shortcut, select Options > Shortcut settings. For example, you can create or change the name of the shortcut. A transfer log is shown after every transfer. To view the log of the last transfer, select a shortcut in the main view and Options > View log. Handle transfer conflicts If an item to be transferred has been edited in both devices, the device attempts to merge the changes automatically. If this is not possible, there is a transfer conflict. Select Check one by one, Priority to this phone, or Priority to other phone to solve the conflict Nokia Ovi Suite Nokia Ovi Suite is a set of applications that you can install to a compatible PC. Ovi Suite groups all available applications in a launcher window from which you can open the applications. Ovi Suite may be included on a memory card, if provided with your device. You can use Ovi Suite to synchronise contacts, calendar, and to-do and other notes between your device and a compatible PC application. You can also use Ovi Suite to transfer bookmarks between your device and compatible browsers, and transfer images and video clips between your device and a compatible PC. Get started Pay attention to synchronisation settings. Data deletion as part of normal synchronisation process is determined by the settings selected. To use Ovi Suite, you need a PC that runs Microsoft Windows XP (SP? or newer) or Windows Vista (SP1 or newer), and is compatible with a USB data cable or with Bluetooth connectivity. Ovi Suite is not compatible with Apple Macintosh computers. For further information on Ovi Suite, see the built-in help, or go to www.nokia.com/support. Install Nokia Ovi Suite Ensure the memory card is inserted in your Nokia E72. Connect the USB cable. Your PC recognises the new device and installs the necessary drivers. This can take several minutes to complete. Select Mass storage as the USB connection mode in your device. Your device is displayed in the Windows file browser as a Removable Disk. Open the root of the memory card drive with the Windows file browser, and select the Ovi Suite installation file. The installation is started. Follow the instructions. Tip: To update Ovi Suite, or if you have problems when installing Ovi Suite from the memory card, copy the installation file to your PC, and install from your PC. Visit Ovi by Nokia OF With Ovi by Nokia, you can find new places and services, and stay in touch with your friends. You can do, for example, the following: Create a mail account Plan trips and view locations on a map Download games, applications, videos, and ringing tones to your device Purchase music The available services may vary by country or region, and not all languages are supported. To access Nokia's Ovi services, go to www.ovi.com, and register your own Nokia account. For more information, go to www.ovi.com/support. About Ove store A With Ovi Store, you can download mobile games, applications, videos, pictures, themes, and ringing tones to your device. Some items are free of charge; others you need to pay for with your credit card or in your phone bill. The availability of payment methods depends on your country of residence and your network service provider. Ovi Store offers content that is compatible with your mobile device and relevant to your tastes and location. 21 Your Nokia E72 22 ~ Your Nokia E72 Your new Nokia Eseries device contains new versions of the Calendar, Contacts, and E-mail applications, as well as a new home screen. Key features Your new Nokia E72 helps you manage your business and personal information. Some of the key features are highlighted here: Read and reply to your e-mail while on the move. Stay up-to-date and plan your meetings with the Calendar application. Manage your business partners and free time friends with the Contacts application. Connect to a wireless LAN (WEAN) with the WLAN wizard application. Work with documents, spreadsheets, and presentations with the Quickoffice application. Find points of interest with the Maps application. Switch from business to personal mode. Edit the appearance and setup of your home screen with the Modes application. Browse your company intranet with the Intranet application. Move your contact and calendar information from a previous device to your Nokia E72 with the Switch application. Check the available updates for applications and download them to your device with the Software update application. Encrypt your device or memory card to prevent outsiders from accessing your important information. Home screen Home screen In the home screen, you can quickly access your most frequently used applications, and view at a glance if you have missed calls or new messages. Whenever you see the icon, scroll right to access a list of available actions. To close the list, scroll left. 130 . - - © Set up e-mail m No calendar entries today Setup Chat WLAN scanning off .......... ......... J Search • (1);) a~ o menu ) 9:05 am Camera The home screen consists of the following: 1. Application shortcuts. To access an application, select the shortcut of the application. Information area To check an item displayed in the information area, select the item. Notification area. To view the notifications, scroll to a box. A box is only visible if there are items in it. You can define two separate home screens for different purposes, for example, one screen to show your business e-mail and notifications, and another to show your personal e-mail. This way, you do not have to see business-related messages outside office hours. To switch between the home screens, select ®. To define which items and shortcuts you want in the home screen, and to set the appearance of the home screen, select Menu > Ctrl. panel and Modes. Work on the home screen To search for contacts in the home screen, start entering the contact's name. Selectthe desired contact from the list of proposed matches. This feature may not be available in all languages. To call the contact, press the call key. To disable the contact search, select Options > Contact search off. To check your received messages, select the message box in the notification area. To read a message, select the message. To access other tasks, scroll right. To view your missed calls, select the calls box in the notification area. To return a call, select a call, and press the call key. To send a text message to a caller, select a call, scroll right, and select Send message from the list of available actions. To listen to your voice mail, selectthe voice mail box in the notification area. Select the desired voice mailbox, and press the call key. One-touch keys With the One-touch keys, you can access applications and tasks quickly. Each key has been assigned an application or a task. To change these, select Menu > Ctrl. panel > Settings and General > Personalisation > One-touch keys. Your service provider may have assigned applications to the keys, in which case you cannot change them. 1 2 1— Home key 2 — Contacts key 3 — Calendar key 23 Your Nokia E72 Your Nokia E72 4 — E-mail key Home key To access the home screen, press the home key briefly. Press the home key briefly again to access the menu. To view the list of active applications, press the home key for a few seconds. When the list is open, press the home key briefly to scroll the list. To open the selected application, press the home key for a few seconds, or press the scroll key. To close the selected application, press the backspace key. Leaving applications running in the background increases the demand on battery power and reduces the battery life. Contacts key To open the Contacts application, press the contacts key briefly. To create a new contact, press the contacts key for a few seconds. Calendar key To open the Calendar application, press the calendar key briefly. To create a new meeting entry, press the calendar key for a few seconds. E-mail key To open your default mailbox, press the e-mail key briefly. To create a new e-mail message, press the e-mail key for a few seconds. Optical Navi key To browse and navigate web pages and maps, and to scroll through lists, slide your finger on the Optical Navi key (scroll key). To scroll through a list, one item at a time, slide your finger slowly on the scroll key. To scroll through a list, ma ny items at a time, or to move around on the display, slide your finger quickly on the scroll key. Capture images — To autofocus in camera, hold your finger on the scroll key. To capture an image, press the scroll key. ~) rat c Optical Navi key settings— To activate or deactivate the Optical Navi key or modify other settings, select Menu > Ctrl. panel > Settings and General > Personalisation > Optical Navi key. 24 Turn to silence calls or alarms When you have activated the sensors in your device, you can silence incoming calls or snooze alarms by turning the device face down. To define the turning options, select Menu > Ctrl. panel > Settings and General > Sensors > Turning control. Calendar About Calendar Select Menu > Calendar. With calendar, you can create and view scheduled events and appointments, and switch between different calendar views. In the month view, calendar entries are marked with a triangle. Anniversary entries are also marked with an exclamation mark. The entries of the selected day are displayed as a list. To open calendar entries, select a calendar view and an entry. Whenever you see the lip. icon, scroll right to access a list of available actions. To close the list, scroll left. Create calendar entries Select Menu > Calendar. You can create the following types of calendar entries: Meeting entries remind you of events that have a specific date and time. Meeting requests are invitations that you can send to the participants. Before you can create meeting requests you must have a compatible mailbox configured to your device. Memo entries are related to the whole day but not to a specific time of the day. Anniversary entries remind you of birthdays and special dates. They refer to a certain day but not a specific time of the day. Anniversary entries are repeated every year. To-do entries remind you of a task that has a due date but not a specific time of the day. To create a calendar entry, select a date, Options > New entry, and the entry type. To set the priority for meeting entries, select Options > Priority. To define how the entry is handled during synchronisation, select Private to hide the entry from viewers if the calendar is available online, Public to make the entry visible to viewers, or None to not copy the entry to your computer. To send the entry to a compatible device, select Options > Send. To make a meeting request of a meeting entry, select Options > Add participants. Create meeting requests 25 Select Menu > Calendar. Your Nokia E72 Your Nokia E72 26 Before you can create meeting requests, you must have a compatible mailbox configured for your device. To create a meeting entry: To create a meeting entry, select a day and Options > > . Enter the names of the required participants. To add names from your contacts list, enter the first few characters, and select from the proposed matches. To add optional participants, select Optio > optional participants. Enter the subject. Enter the start and end times and dates, or select All-day event. Enter the location. Set an alarm for the entry, if needed. For a recurring meeting, set the recurrence time, and enter the end date. Enter a description. To set the priority for the meeting request, select Options > Priority. To send the meeting request, select Options > Send. Calendar views Select Menu > Calendar. You can switch between the following views: Month view shows the current month and the calendar entries of the selected day in a list. Week view shows the events for the selected week in seven day boxes. Day view shows the events for the selected day grouped into time slots according to their starting time. To-do view shows all to-do items. Agenda view shows the events for the selected day in a list. To change the view, select Options > Change view and the desired view. Tip: To open the week view, select the week number. To move to the next or the previous day in month, week, day, and agenda view, select the desired day. To change the default view, select Options > Settings > Default view. Contacts About Contacts Select Menu > Contacts. With Contacts, you can save and update contact information, such as phone numbers, home addresses, and e-mail addresses of your contacts. You can add a personal ringing tone or a thumbnail image to a contact. You can also create contact groups, which allow you to communicate with several contacts at the same time, and send contact information to compatible devices. Whenever you see the icon, scroll right to access a list of available actions. To close the list, scroll left. Work with contacts Select Menu > Contacts. To create a contact, select Options > New contact, and enter the details of the contact. To copy contacts from the memory card, if available, select Options > Create backup > Memory card to phone. To search for contacts, start entering the contacts name in the search field. Create contact gr uup. Select Menu > Contacts. To create a contact group, scroll to each contact you want to add to the group, and select Options > Mark/ Unmark > Mark. Select Options > Group > Add to group > Create new group, and enter a name for the group. If you want to make conference calls to the group using a conference service, define the following: Conf. service number — Enter the conference call service number. Conf. service ID — Enter the conference call ID. Conf. service PIN — Enter the conference call PIN code. To make a conference call to the group using the conference service, selectthe group, scroll right, and select Call conf. service. Search for contacts in a remote database To activate remote contact search, select Options > Settings > Contacts > Remote search server. You must define a remote server before you can do remote contact searches. To search for contacts in a remote database, select Contacts > Options > Search from remote. Enter the name of the contact you want to search for, and select Search. The device establishes a data connection to the remote database. To search for contacts in the home screen, start entering characters in the home screen, and select the database from the proposed matches. To change the remote contacts database, select Options > Settings > Contacts > Remote search server. This setting affects the database used in the Contacts and Calendar applications and the home screen, but not the database that is used for e-mail. *rid ringing tones for contacts Select Menu > Contacts. To add a ringing tone for a contact, select the contact, Options > Ringing tone, and a ringing tone. The ringing tone sounds when the contact calls you. To add a ringing tone for a contact group, select the contact group, Options > Group > Ringing tone, and a ringing tone. 27 Your Nokia E72 Your Nokia E72 28 To remove the ringing tone, select Default tone from the list of ringing tones. Contacts settings Select Menu > Contacts. To modify the settings of the Contacts application, select Options > Settings > Contacts and from the following: Contacts to display — Show contacts that are stored in the device memory, on the SIM card, or both. Default saving memory — Select where to save contacts. Name display — Change the way contacts' names are displayed. This setting is not available for all languages. Default contact list — Select which contacts list opens when you open the Contacts application. This setting is only available when there is more than one contacts list. Remote search server — Change the remote contacts database. This option is available only if remote contacts databases are supported by your service provider. Multitasking You can have several applications open at the same time. To switch between active applications, press and hold the home key, scroll to an application, and press the scroll key. To close the selected application, press the backspace key. pExample: When you have an active phone call and want to check your calendar, press the home key to access the menu, and open the Calendar application. The phone call remains active in the background. Example: When you are writing a message and want to check a web site, press the home key to access the menu, and open the Web application. Select a bookmark or enter the web address manually, and select Go to. To return to your message, press and hold the home key, scroll to the message and press the scroll key. Flashlight The camera flash can be used as a flashlight. To switch the flashlight on or off, in the home screen, press and hold the space bar. Do not point the flashlight at anyone's eye. Ovi Files With Ovi Files, you can use your Nokia E72 to access content on your computer if it is switched on and connected to the internet. You will need to install the Ovi Files application on every computer you want to access with Ovi Files. With Ovi Files, you can: Browse, search, and view your images. You do not need to upload the images to the website but you can access your computer content with your mobile device. Browse, search, and view your files and documents. Transfer files from your computer to your device. Send files and folders from your computer without moving them to your device first. Access files on your computer even when your computer is switched off. Just choose which folders and files you want to be available, and Ovi Files Make calls Voice calls In the home screen, enter the phone number, including the area code. To remove a number, press the backspace key. For international calls, press + (+ replaces the international access code), and enter the country code, area code (omit the leading zero if necessary), and phone number. To make the call, press the call key. To end the call (or to cancel the call attempt), press the end key. Pressing the end key always ends a call, even if another application is active. To make a call from the contacts list, select Menu > Contacts. Scroll to the desired name, or enter the first letters or characters of the name to the search field. To call the contact, press the call key. If you have saved several numbers for a contact, select the desired number from the list, and press the call key. automatically keeps an up-to-date copy stored in a protected, online storage for access even when your computer is switched off. For support, see files.ovi.com/support. Options during a call To adjust the volume during a call, use the volume key on the side of your device. You can also use the scroll key. If you have set the volume to Mute, select Unmute first. To send an image or a video clip in a multimedia message to the other participant of the call, select Options > Send MMS (in 3G networks only). You can edit the message and change the recipient before sending. Press the call key to send the file to a compatible device (network service). To put an active voice call on hold while answering another incoming call, select Options > Hold. To switch between the active and the held call, select Options > Swap. To send DTMF tone strings (for example, a password), select Options > Send DTMF. Enter the DTMF string or search for it in Contacts. To enter a wait character (w) or a pause character (p), press * repeatedly. To send the tone, select OK. You can add DTMF tones to the phone number or DTMF fields in a contact card. 29 H I'Q V d Y X Tip: When you have only one active voice call, to put the call on hold, press the call key. To activate the call, press the call key again. During an active call, to route the sound from the handset to the loudspeaker, select Options > Activate loudspeaker. If you have attached a compatible headset with Bluetooth connectivity, to route the sound to the headset, select Options > Activate handsfree. To switch back to the handset, select Options > Activate To end an active call and replace it by answering the waiting call, select Options > Replace. If you have several calls active, to end them all, select Options > End all calls. Many of the options that you can use during a voice call are network services. Voice mail Q Select > > > When you open the Voice mail application (network service) for the first time, you are asked to enter the number of your voice mailbox. To call your voice mailbox, scroll to Voice mailbox, and select Options > Call voice mailbox. To call your video mailbox, scroll to Video mailbox, and select Options > Call video mailbox. If you have configured net call settings to your device and 30 have an internet call mailbox, to call the mailbox, scroll to the mailbox, and select mbx.. To call your mailbox in the home screen, press and hold 1; or press land then the call key. Select the mailbox you want to call. To change the mailbox number, select the mailbox and Options > Change number. Answer or decline a call To answer the call, press the call key. To mute the ringing tone of an incoming call, select ence. If you do not want to answer a call, press the end key. If you activate the Call divert > Voice calls > If busy function in phone settings to divert calls, declining an incoming call also diverts the call. When you select Silence to mute the ringing tone of an incoming call, you can send a text message without rejecting the call, informing the caller that you cannot answer the call. Select Options > Send message. To activate or deactivate rejecting calls with a text message, select Menu > Ctrl. panel > Settings and Phone > Call > Reject call with message. To edit the content of the message sent to the caller, select Message text. Make a conference call i. Make a call to the first participant. To make a call to another participant, select Optic > New call. The first call is put on hold. When the new call is answered, to join the first participant in the conference call, select > Conference. To add a new person to the call, repeat step 2, and select Options > Conference > Add to conference. Your device supports conference calls between a maximum of six participants, including yourself. To have a private conversation with one of the participants, select Options > Conference > Private. Select a participant, and select Private. The conference call is put on hold on your device. The other participants can still continue the conference call. After you finish the private conversation, select > Conference to return to the conference call. To drop a participant, select > > Drop participant, scroll to the participant, and select Drop. To end the active conference call, press the end key. Speed dial a phone number To activate the feature, select Menu > Ctrl. panel > Settings and Phone > Call > Speed dialling. 1. To assign a phone number to one of the number keys (2-9), select Menu > Ctrl. panel > Phone > Speed dial. 2. Scroll to the keyto which you want to assign the phone number, and select Options > Assign. 1 is reserved for the voice or video mailbox. To call an assigned number, in the home screen, press the assigned key and then the call key. Call waiting You can answer a call while you have another call in progress. To activate call waiting (network service), select Menu > Ctrl. panel > Settings and Phone > Call > Call waiting. To answer the waiting call, press the call key. The first call is put on hold. To switch between the two calls, select Swap. To connect an incoming call or a call on hold with an active call and to disconnect yourself from the calls, select Options > . To end the active call, press the end key. To end both calls, select Options > End all calls. Call divert Select Menu > Ctrl. panel > Settings and Phone > Call divert. Divert incoming calls to your voice mailbox or to another phone number. For details, contact your service provider. Select the type of calls to divert and from the following: • All voice calls or All fax calls — Divert all incoming voice or fax calls. You cannot answer the calls, only 31 divert the calls to another number. If busy — Divert incoming calls if you have an active call. If not answered — Divert incoming calls after your device rings fora specified length of time. Select the length of time for the device to ring before diverting the call. If out of reach — Divert calls when the device is switched off or out of network coverage. If not available — Divert calls if you have an active call, do not answer, or the device is switched off or out of network coverage. To divert calls to your voice mailbox, select a call type, a diverting option, andOptions > Activate > To voice mailbox. To divert calls to another phone number, select a call type, a diverting option, and Options > Activate > To other number. Enter the number, or select Find to retrieve a number saved in Contacts. To check the current diverting status, scroll to the diverting option, and select Options > Check status. To stop diverting calls, scroll to the diverting option, and select Options > Deactivate. Select from the following voice call barring settings: Outgoing calls — Prevent making voice calls with your device. Incoming calls — Prevent incoming calls. International calls — Prevent calling to foreign countries or regions. Incoming calls when roaming — Prevent incoming calls when outside your home country. International calls except to home country — Prevent calls to foreign countries or regions, but allow calls to your home country. To check the status of voice call barrings, select the barring option and Options > Check status. To deactivate all voice call barrings, select a barring option and Options > Deactivate all barrings. To change the password used for barring voice and fax calls, select Options > Edit barring password. Enter the current code, then the new code twice. The barring password must be four digits long. For details, contact your service provider. Voice dialling mAd barring Select Menu > Ctrl. panel > Settings and Phone > Call barring. If you have defined internet call settings, select Internet call barring. You can bar the calls that can be made or received with the device (network service). To modify the settings, you 32 need the barring password from your service provider. Call barring affects all call types. Your device supports enhanced voice commands. Enhanced voice commands are not dependent on the speaker's voice, so you do not need to record voice tags in advance. The device creates a voice tag for the entries in the contacts, and compares the spoken voice tag to it. The voice recognition in the device adapts to the main user's voice to recognise the voice commands better. The voice tag for a contact is the name that is saved for the contact. To listen to the synthesised voice tag, select a H contact and Options > Voice tag details. Scroll to a contact detail, and select Options > Play voice tag. Make a call with a voice tag ONote: Using voice tags may be difficult in a noisy environment or during an emergency, so you should not rely solely upon voice dialling in all circumstances. When you use voice dialling, the loudspeaker is in use. Hold the device at a short distance away when you say the voice tag. To start voice dialling, in the home screen, press and hold the right selection key. If a compatible headset with the headset key is attached, press and hold the headset key to start voice dialling. Ashorttone sounds, and Speak now is displayed. Say clearly the name that is saved for the contact. The device plays a synthesised voice tag for the recognised contact, and displays the name and number. If you do not want to call that contact, select another contact from the list of matches within 2.5 seconds, or, to cancel, select Quit. If several numbers are saved for a name, the device selects the default number, if defined. Otherwise, the device selects the first available number in a contact card. You can also say the name and telephone number type, such as mobile or home. Make a video call When you make a video call (network service), you can see a real-time, two-way video between you and the recipient of the call. The live video image, or video image captured by the camera in your device is shown to the video call recipient. To be able to make a video call, you must have a USIM card and be in the coverage of a 3G network. For availability of and subscription to video call services, contact your network service provider. A video call can only be made between two parties. The video call can be made to a compatible mobile device or an ISDN client. Video calls cannot be made while another voice, video, or data call is active. Icons You are not receiving video (the recipient is not sending video or the network is not transmitting it). You have denied video sending from your device. To send a still image instead, select Menu > Ctrl. panel > Settings and Phone > Call > Image in video call. Even if you denied video sending during a video call, the call is still charged as a video call. Check the pricing with your service provider. To start a video call, enter the phone number in the standby mode, or select Contacts and a contact. Select Options > Call > Video call. The secondary camera on the front is used by default for video calls. Starting a video call may take a while. Waiting for video image is shown. If the call is not successful (for example, video calls are not supported by the network, or the receiving device is not compatible), you are asked if you want to try a normal call or send a text or multimedia message instead. 33 H The video call is active when you see two video images, ra and hear the sound through the loudspeaker. The call u recipient may deny video sending (Z), in which case you only hear the sound and may see a still image or a Y grey background graphic. ra 3. To end the video call, press the end key. Options during a video call To change between showing video or hearing only sound, select Options > Enable, or Disable and the desired option. To use the main camera to send video, select Options > Use main camera. To switch back to the secondary camera, select Options > Use secondary camera. To take a snapshot of the video you are sending, select Options > Send snapshot. Video sending is paused and the snapshotis shown to the recipient. The snapshot is not saved. Press Cancel to resume sending video. To zoom your image in or out, select Options > Zoom. To route the audio to a compatible headsetwith Bluetooth connectivity attached to your device, select Options > Activate handsfree. To route the audio back to the loudspeaker of your device, select Options > Activate handset. To change the video quality, select Options > Video preference. Normal quality is framerate 10 fps. Use 34 Clearer detailfor small, static details. Use Smoother motion for moving images. To adjust the volume during a video call, use the volume key on the side of the device. Answer or decline a video call When a video call arrives, okk is displayed. To answer the video call, press the call key. Allow video image to be sent to caller? is displayed. To start sending live video image, select Yes. If you do not activate the video call, you only hear the sound of the caller. A grey screen replaces the video image. To replace the grey screen with a still image captured by the camera in your device, select Menu > Ctrl. panel > Settings and Phone > Call > Image in video call. To end the video call, press the end key. Video sharing Use video sharing (network service) to send live video or a video clip from your mobile device to another compatible mobile device during a voice call. The loudspeakeris active when you activate video sharing. If you do not want to use the loudspeaker for the voice call while you share video, you can also use a compatible headset. °Warning: Continuous exposure to high volume may damage your hearing. Listen to music at a moderate level, and do not hold the device near your ear when the loudspeaker is in use. viaeo snaring requirements Video sharing requires a 3G connection. For more information on the service, 3G network availability, and fees associated with using this service, contact your service provider. To use video sharing you must do the following: Ensure that your device is set up for person-to-person connections. Ensure you have an active 3G connection and are within 3G network coverage. If you move outside the 3G network during a video sharing session, the sharing stops while your voice call continues. Ensure that both the sender and recipient are registered to the 3G network. If you invite someone to a sharing session and the recipient's device is not within 3G network coverage, does not have video sharing installed, or person-to-person connections set up, the recipient does not receive invitations. You receive an error message that indicates that the recipient cannot accept the invitation. Settings To set up video sharing, you need person-to-person and 3G connection settings. Person-to-person connection settings A person-to-person connection is also known as a Session Initiation Protocol (SIP) connection. The SIP profile settings must be configured in your device before you can use video sharing. Ask your service provider for the SIP profile settings, and save them in your device. Your service provider may send you the settings or give you a list of the needed parameters. To add a SIP address to a contact card: Select > Contacts. Open the contact card (or start a new card for that person). Select Options > Add detail > Share video. Enter the SIP address in the format username@domainname (you can use an IP address instead of a domain name). If you do not know the SIP address for the contact, you can use the phone number of the recipient, including the country code, to share video (if supported by the network service provider). 3G connection settings To set up your 3G connection: Contactyour service providerto establish an agreement for you to use the 3G network. Ensure that your device 3G access point connection settings are configured properly. snare u ve viaeo or video clips During an active voice call, select Options > Share video. 1. To share live video during the call, select Live video. 35 To share a video clip, select Video clip and the clip you want to share. You may need to convert the video clip into a suitable formatto be able to share it. If your device notifies you that the video clip must be converted, select . Your device must have a video editor for the conversion to work. If the recipient has several SIP addresses or phone numbers including the country code saved in the contacts list, select the desired address or number. If the SIP address or phone number of the recipientis not available, enter the address or number of the recipient including the country code, and select OK to send the invitation. Your device sends the invitation to the SIP address. Sharing begins automatically when the recipient accepts the invitation. Options during video sharing CI Zoom the video (available for sender only). ,:, Adjust the brightness (available for sender only). or en Mute or unmute the microphone. )) or .' Turn the loudspeaker on and off. 9,, or O Pause and resume video sharing. pi Switch to full screen mode (available for receiver only). To end the sharing session, select Stop. To end the voice call, press the end key. When you end the call, video sharing also ends. 36 To save the live video you shared, select Yes when prompted. The device notifies you of the memory location of the saved video. To define the preferred memory location, select Menu > Ctrl. panel > Settings and Connection > Video sharing > Preferred saving memory. If you access other applications while you are sharing a video clip, the sharing is paused. To return to the video sharing view, and to continue sharing, in the home screen, select Options > Continue. Accept an invitation When someone sends you a video sharing invitation, the invitation message displays the sender's name or SIP address. If your device is not set to silent, it rings when you receive an invitation. If someone sends you a share invitation and you are not within UMTS network coverage, you will not knowthatyou received an invitation. When you receive an invitation, select from the following: Yes — Accept the invitation, and activate the sharing session. No — Reject the invitation. The sender receives a message that you rejected the invitation. You can also press the end key to reject the invitation and end the voice call. To mute the video on your device, select Options > Mute. To playthe video at the original volume, select Options > Original volume. This does not affect the audio playback of the other party of the phone call. To end the sharing session, select Stop. To end the voice call, press the end key. When you end the call, also video sharing ends. To view the approximate duration of your last call, and dialled and received calls, select Call duration. Log 4f The log stores information about the communication history of the device. The device registers missed and received calls only if the network supports these functions, the device is switched on, and within the network service area. Recent calls Select Menu > Log and Recent calls. To view missed, received, and dialled calls, select Missed calls, Received calls or Dialled numbers. OTip: To open the dialled numbers list in the home screen, press the call key. Select Options and from the following: Save to Contacts — Save the highlighted phone number from a recent calls list to your contacts. Clear list — Clear the selected recent calls list. Delete — Clear a highlighted event in the selected list. Settings — Select Log duration and the length of time that the communication information is saved in the log. If you select No log, no information is saved in the log. Call duration Select Menu > Log. Packet data Select Menu > Log. You may be charged for your packet data connections by the amount of data sent and received. To check the amount of data sent or received during packet data connections, select Packet data > All sent dataor All received data. To clear both sent and received information, select Options > Clear counters. You need the lock code to clear the information. Monitor all communication events Select Menu > Log. To open the general log where you can monitor all voice calls, text messages, or data and wireless LAN connections registered by the device, select the general log tab [1+4. Subevents, such as a text message sent in more than one part and packet data connections, are logged as one communication event. Connections to your mailbox, multimedia messaging centre, or web pages are shown as packet data connections. To view how much data was transferred and how long a certain packet data connection lasted, scroll to an incoming or outgoing event indicated by Pack., and select Options > View. 37 To copy a phone number from the log to the clipboard, and paste it into a text message, for example, select Options > Use number > Copy. To filter the log, select Options > Filter and a filter. To set the log duration, select Options > Settings > Log duration. If you select No log, all the log contents, recent calls register, and messaging delivery reports are permanently deleted. Messaging Select Menu > Messaging. In Messaging (network service), you can send and receive text messages, multimedia messages, audio messages, and e-mail messages. You can also receive web service messages, cell broadcast messages, and special messages containing data, and send service commands. Before sending or receiving messages, you may need to do the following: Insert a valid SIM card in the device and be located in the service area of a cellular network. Verify that the network supports the messaging features you want to use and that they are activated on your SIM card. Define the internet access point settings on the device. Define the e-mail account settings on the device. Define the text message settings on the device. Define the multimedia message settings on the device. The device may recognise the SIM card provider and automatically configure some of the message settings. If 38 not, you may need to define the settings manually; or contact your service provider to configure the settings. Messaging folders Select Menu > Messaging. Messages and data received using Bluetooth connectivity are stored in the Inbox folder. E-mail messages are stored in the Mailbox folder. Messages that you have been writing can be stored in the Drafts folder. Messages that are waiting to be sent are stored in the Outbox folder, and messages that have been sent, excluding Bluetooth messages, are stored in the Sent folder. Tip: Messages are placed in the Outbox folder, for example, when your device is outside network coverage. ONote: The message sent icon or text on your device screen does not indicate that the message is received at the intended destination. To request the network to send you a delivery report of the text messages and multimedia messages you have sent(networkservice),selectOptions > Settings > Text message > Receive report or Multimedia message > Receive reports. The reports are saved in the Reports folder. Organise messages Select Menu > Messaging and My folders. To create a new folder to organise your messages, select Options > New folder. To rename a folder, select Options > Rename folder. You can only rename folders that you have created. To move a message to another folder, select the message, Options > Move to folder, the folder, and OK. To sort messages in a specific order, select Options > Sort by. To view the properties of a message, select the message and Options > Message details. Nokia Messaging The Nokia Messaging service automatically pushes e-mail from your existing e-mail address to your Nokia E72. You can read, respond to, and organise your e-mails on the go. The Nokia Messaging service works with a number of internet e-mail providers that are often used for personal e-mail, such as Google e-mail services. The Nokia Messaging service must be supported by your network and may not be available in all regions. Install the Nokia Messaging application 1. Select Menu > Email > New mailb.. Read the information on the display, and select If requested, allow your device to connect to the internet. Select your e-mail service provider or account type. Enter the required account details, such as e-mail address and password. The Nokia Messaging service can run on your device even ifyou have installed other e-mail applications, such as Mail for Exchange. E-mail Set up your e-mail With the E-mail wizard, you can set up your corporate e­mail account, such as Mail for Exchange, and your internet e-mail account. When setting up your corporate e-mail, you may be prompted for the name of the server associated with your e-mail address. For details, contact your company IT department. To open the wizard, in the home screen, select Set up e-mail. Enter your e-mail address and password. If the wizard is not able to configure your e-mail settings automatically, you need to select your e-mail account type, and enter the related account settings. If your device contains any additional e-mail clients, those are offered to you when you open the wizard. 39 c Send e-mail 5i Select Menu > Messaging. H 1. Select your mailbox and Options > Create email. 2. In the To field, enter the recipient's e-mail address. If the recipient's e-mail address can be found in Contacts, start entering the recipient's name, and select the recipient from the proposed matches. If you add several recipients, insert; to separate the e-mail addresses. Use the Cc field to send a copy to other recipients, or the Bcc field to send a blind copy to recipients. If the Bcc field is not visible, select Options > More > Show Bcc field. In the Subject field, enter the subject of the e-mail. Enter your message in the text area. Select Options and from the following: Add attachment — Add an attachment to the message. Priority — Set the priority of the message. Flag — Flag the message for follow-up. Insert template — Insert text from a template. Add recipient — Add recipients to the message from Contacts. Editing options — Cut, copy, or paste the selected text. Input options —Activate or deactivate predictive text input, or select the writing language. 6. Select Options > Send. The available options may vary. 40 Add attachments Select Menu > Messaging. To write an e-mail message, select your mailbox and Options > Create email. To add an attachment to the e-mail message, select Options > Add attachment. To remove the selected attachment, select Options > Remove attachment. Read e-mail Select Menu > Messaging. Important: Exercise caution when opening messages. Messages may contain malicious software or otherwise be harmful to your device or PC. To read a received e-mail message, selectthe mailbox, and select the message from the list. To reply to the message sender, select Options > Reply. To reply to the sender and all other recipients, select Options > Reply to all. To forward the message, select Options > Forward. Download attachments Select Menu > Messaging and a mailbox. To view the attachments in a received e-mail message, scroll to the attachment field, and select Options > Actions. If there is one attachment in the message, select Open to open the attachment. If there are several attachments, select View list to see a list showing which attachments have been downloaded. To download the selected attachment or all the attachments from the list to your device, select Options > Actions > Download or Download all. The attachments are not saved in your device, and are deleted when you delete the message. To save the selected attachment or all the downloaded attachments in your device, select Options > Actions > Save or Save all. To open the selected, downloaded attachment, select Options > Actions > Open. Reply to a meeting request Select Menu > Messaging and a mailbox. Select a received meeting request, Options, and from the following: Accept — Accept the meeting request. Decline — Decline the meeting request. Forward — Forward the meeting request to another recipient. Remove from calendar — Remove a cancelled meeting from your calendar. To search for items within the recipients, subjects, and body texts of the e-mail messages in the mailbox, select Options > Search. To stop the search, select Options > Stop search. To start a new search, select Options > New search. Delete e-mails Select Menu > Messaging and a mailbox. To delete an e-mail message, select the message and Options > Actions > Delete. The message is placed in the Deleted items folder, if available. If there is no Deleted items folder available, the message is deleted permanently. To empty the Deleted items folder, select the folder and Options > Empty deleted items. Switch between e-mail folders Select Menu > Messaging and a mailbox. To open another e-mail folder or mailbox, select Inbox at the top of the display. Select the e-mail folder or mailbox from the list. Search for e-mail messages Select Menu > Messaging and a mailbox. Disconnect from the mailbox Select Menu > Messaging and a mailbox. To cancel the synchronisation between the device and the e-mail server, and to work with e-mail without a wireless connection, select Options > Disconnect. If your mailbox 41 IT does not have the Disconnect option, select Options > Exit to disconnect from the mailbox. Al To start the synchronisation again, select Options > Connect. H CU Set an out-of-office reply Select Menu > Email. To set an out-of-office reply, if available, select your mailbox and Options > Settings > Mailbox settings. Depending on the mailbox type, select either Mailbox > Out of office > On or Mailbox settings > Out of office > On. To enter the text for the reply, select Out of office reply. General e-mail settings Select Menu > Email and Settings > Global settings. Select from the following: Message list layout — Select whether the e-mail messages in Inbox display one or two lines of text. Body text preview — Preview messages when scrolling through the list of e-mail messages in Inbox. Title dividers —To be able to expand and collapse the list of e-mail messages, select On. Download notifications — Set the device to display a notification when an e-mail attachment has been downloaded. Warn before delete — Set the device to display a warning before you delete an e-mail message. 42 • Home screen — Define how many lines of e-mail are displayed in the home screen information area. Message reader With Message reader you can listen to text, multimedia, audio, and e-mail messages. To listen to new messages or e-mail, in the home screen, press and hold the left selection key until Message reader opens. To listen to a message from your Inbox, scroll to the message, and select Options > Listen. To listen to an e­mail message from your mailbox, scroll to the message, and selectOptions > Listen. To stop the reading, press the end key. To pause and continue the reading, press the scroll key. To skip to the next message, scroll right. To replay the current message or e-mail, scroll left. To skip to the previous message, scroll left at the beginning of the message. To view the current message or e-mail in text format without the sound, select Options > View. Speech Select Menu > Ctrl. panel > Phone > Speech. With Speech, you can set the language, voice, and voice properties for the message reader. To set the language for the message reader, select Language. To download additional languages to your device, select Options > Download languages. When you download a new language, you must download at least one voice for that language. To set the speaking voice, select Voice. The voice depends on the selected language. To set the speaking rate, select Speed. To set the speaking volume, select Volume. To view the details of a voice, open the voice tab, and select the voice and Options > Voice details. To listen to a voice, select the voice and Options > Play voice. To delete languages or voices, select the item and Options > Delete. Text and multimedia messages Select Menu > Messaging. Only devices that have compatible features can receive and display multimedia messages. The appearance of a message may vary depending on the receiving device. A multimedia message (MMS) can contain text and objects such as images, sound clips, or video clips. Before you can send or receive multimedia messages on your device, you must define the multimedia message settings. Your device may recognise the SIM card provider and configure the correct multimedia message settings automatically. If not, contactyour service provider for the correctsettings, order the settings from your service provider in a configuration message, or use the Settings wizard application. Write and send messages Select Menu > Messaging. Important: Exercise caution when opening messages. Messages may contain malicious software or otherwise be harmful to your device or PC. Before you can create a multimedia message or write an e-mail, you must have the correct connection settings in place. The wireless network may limit the size of MMS messages. If the inserted picture exceeds this limit, the device may make it smaller so that it can be sent by MMS. Check the size limit of e-mail messages with your service provider. If you attempt to send an e-mail message that exceeds the size limit of the e-mail server, the message is leftin the Outboxfolder, and the device attempts to resend it periodically. Sending an e-mail requires a data connection, and continuous attempts to resend the e-mail may increase your data transfer costs. In the Outbox folder, you can delete such a message, or move it to the Drafts folder. Select New message > Message to send a text or multimedia message (MMS), Audio message to send a multimedia message that includes one sound clip, or E-mail to send an e-mail message. In the To field, press the scroll key to select recipients or groups from the contacts list, or enter the recipient's phone number or e-mail address. You can also copy and paste the number or address from the clipboard. In the subject field, enter the subject of the e-mail. To change the fields that are visible, select Options > Message header fields. 43 44 In the message field, write the message. To insert a template or note, select Options > Insert content > Insert text > Template or N- . To add a media file to a multimedia message, select Options > Insert content, the file type or source, and the desired file. To insert a business card, slide, note, or some other file to the message, select Options > Insert content > Insert other. To capture an image or record a video or sound clip for a multimedia message, select Options > Insert content > Insert image > New, Insert video clip > New, or Insert sound clip > New. To add an attachment to an e-mail, select Options and the attachment type. E-mail attachments are indicated by g. To send the message, select > , or press the call key. 40/Note: The message sent icon or text on your device screen does not indicate that the message is received at the intended destination. Your device supports text messages beyond the limit for a single message. Longer messages are sent as two or more messages. Your service provider may charge accordingly. Characters with accents, other marks, or some language options take more space, and limit the number of characters that can be sent in a single message. You may not be able to send video clips that are saved in the MP4 file format or that exceed the size limit of the wireless network in a multimedia message. Text messages on the SIM card Select Menu > Messaging and ¶lptions > SIM messages. Text messages may be stored on your SIM card. Before you can view SIM messages, you must copy the messages to a folder in the device. After copying the messages to a folder, you can view them in the folder or delete them from the SIM card. Select Options > Mark/Unmark > Mark or Mark all to mark every message. Select Options > Copy. Select a folder and OK to begin copying. To view SIM card messages, open the folder where you copied the messages, and open a message. Receive and reply to multimedia messages 0Important: Exercise caution when opening messages. Messages may contain malicious software or otherwise be harmful to your device or PC. Tip: If you receive multimedia messages that contain objects unsupported by your device, you cannot open them. Try to send these objects to another device such as a computer, and open them there. 1. To reply to a multimedia message, open the message, and select Options > Reply. Select To sender to reply to the sender, To all to reply to everyone included in the received message, Via audio message to reply with an audio message, or Via e-mail to reply with an e-mail message. E-mail message is available onlyifa mailbox is configured and the message is sent from an e-mail address. Enter the text of the message, and select Optioi > Send. Create presentations Select Menu > Messaging. Creating multimedia presentations is not possible if MMS creation mode is set to Restricted. To change the setting, select Options > Settings > Multimedia message > MMS creation mode > Free or Guided. To create a presentation, select New message > Message. The message type is changed to multimedia message based on the inserted content. In the To field, enter a recipients number or e-mail address, or press the scroll key to add a recipient from the contacts list. If you enter more than one number or e-mail address, separate them with a semicolon. Select Options > Insert content > Insert presentation and a presentation template. A template may define which media objects you can include in the presentation, where they appear, and which effects are displayed between images and slides. Scroll to the text area, and enter the text. To insert images, sound or video clips, or notes in your presentation, scroll to the corresponding object area, and select Options > Insert. To add slides, select Options > Insert > New slide. To select the background colour for the presentation and background images for different slides, select Options > Background settings. To set effects between images or slides, select Options > Effect settings. To preview the presentation, select Options > Preview. Multimedia presentations may only be viewed in compatible devices that support presentations. They may appear different in different devices. View presentations To view a presentation, open the multimedia message from the Inboxfolder. Scroll to the presentation, and press the scroll key. To pause the presentation, press either selection key. To resume playing the presentation, select Options > Continue. If the text or images are too large to fit on the display, select Options > Activate scrolling, and scroll to see the entire presentation. To find phone numbers and e-mail or web addresses in the presentation, select Options > Find. You may use these numbers and addresses to make calls, send messages, or create bookmarks, for example. 45 g View and save multimedia 'r attachments H To view multimedia messages as complete presentations, d open the message, and select Options > Play E presentation. Tip: To view or play a multimedia object in a To define the service message settings, select Options > Settings > Service message. To download the service or message content, select Options > Download message. To view information about the sender, web address, expiration date, and other details of the message before downloading it, select Options > Message details. multimedia message, select View image, Play sound clip, or Play video clip. To view the name and size of an attachment, select the message and Options > Objects. To save a multimedia object, select Options > Objects, the object, and Options > Save. Special message types Select Menu > Messaging. You can receive special messages that contain data, such as operator logos, ringing tones, bookmarks, or internet access or e-mail account settings. To save the contents of these messages, select Options > Save. Service messages Service messages are sent to your device by service providers. Service messages may contain notifications such as news headlines, services, or links through which 46 the message content can be downloaded. Send service commands You can send a service request message (also known as a USSD command) to your service provider and request activation for certain network services. Contact your service provider for the service request text. To send a service request message, select Options > Service commands. Enter the service request text and select Options > Send. Cell broadcast Select Menu > Messaging and Options > Cell broadcast. With the cell broadcast network service, you can receive messages on various topics from your service provider, such as weather or traffic conditions in a particular region. For available topics and relevant topic numbers, contact your service provider. Cell broadcast messages cannot be received when the device is in the remote SIM mode. A packet data (GPRS) connection may prevent cell broadcast reception. Cell broadcast messages cannot be received in UMTS (3G) networks. To receive cell broadcast messages, you may need to turn cell broadcast reception on. Select Options > Settings > Reception > On. To view messages related to a topic, select the topic. To receive messages related to a topic, select Optior > Subscribe. OTip: You can set important topics as hot topics. You are notified in the home screen, when you receive a message related to a hot topic. Select a topic and Options > Hotmark. To add, edit, or delete topics, select Options > Topic. Messaging settings Select Menu > Messaging and Options > Settings. Open the message type in question, and define all fields marked with Must be defined or with a red asterisk. Your device may recognise the SIM card provider and configure the correct text message, multimedia message, and GPRS settings automatically. If not, contact your service provider for the correct settings, order the settings from your service provider in a configuration message, or use the Settings wizard application. Select from the following: Message centres — View the available message centres for your device, or add a new one. Message centre in use — Select a message centre to send the message. Character encoding — Select Reduced support to use automatic character conversion to another encoding system when available. Receive report — Select Yes if you want the network to send you delivery reports on your messages (network service). Message validity — Select how long the message centre resends your message if the first attempt fails (network service). If the recipient cannot be reached within the validity period, the message is deleted from the message centre. Message sent as — Convert the message to another format, for example, fax or e-mail. Change this option only if you are sure that your message centre is able to convert text messages into these other formats. For more information, contact your service provider. Preferred connection — Select the preferred method of connection when sending text messages from your device. Reply via same centre — Select whether you want the reply message to be sent using the same text message centre number (network service). Text message settings Select Menu > Messaging and Options > Settings > Text message. Multimedia message settings Select Menu > Messaging and Options > Settings > Multimedia message. Select from the following: 47 48 Image size — Scale images in multimedia messages. MMS creation mode — Select Restricted to set your device to prevent you from including content in multimedia messages that may not be supported bythe network or the receiving device. To receive warnings about including such content, select Guided. To create a multimedia message with no restrictions on attachment type, select . If you select Restricteu, creating multimedia presentations is not possible. Access point in use — Select the default access point to connect to the multimedia message centre. You may not be able to change the default access point if it is preset in your device by your service provider. Multimedia retrieval — Select how you want to receive messages, if available. Select Always automatic to receive multimedia messages always automatically, Auto in home netw. to receive notification of a new multimedia message that you can retrieve from the message centre (for example, when you are travelling abroad and are outside your home network), Manual to retrieve multimedia messages from the message centre manually, or to prevent receipt of any multimedia messages. Automatic retrieval may not be supported in all regions. pow anonymous msgs. — Receive messages from unknown senders. Receive adverts — Receive messages defined as advertisements. Receive reports — Request for delivery and read reports of sent messages (network service). Receiving a delivery report of a multimedia message that has been sent to an e-mail address may not be possible. Deny report sending —Select to not send delivery reports from your device for received multimedia messages. Message validity — Select how long the messaging centre tries to send the message (network service). If the recipient of a message cannot be reached within the validity period, the message is removed from the multimedia messaging centre. Maximum time is the maximum amount of time allowed by the network. The device requires network support to indicate that a sent message has been received or read. Depending on the network and other circumstances, this information may not always be reliable. service message settings Select Menu > Messaging and Options > Settings > Service message. To allow your device to receive service messages from your service provider, select Service messages > On. To select how to download services and service message content, select Download messages > Automatically or rianually. If you select Automatically, you may still need to confirm some downloads since not all services can be downloaded automatically. Cell broadcast settings Select Menu > Messagir and Options > Settings > Cell broadcast. To receive cell broadcast messages, select Reception > On. To select the languages in which you want to receive cell broadcast messages, select Language. To display new topics in the cell broadcasttopics list, select Topic detection > On. Other settings Select Menu > Messaging and Options > Settings > Other. Select from the following: Save sent messages — Select whether to save sent messages in the Sent folder. Number of saved msg — Enter the number of sent messages to save. When the limit is reached, the oldest message is deleted. Memory in use —Select where to save your messages. You can save messages to the memory card only if a memory card is inserted. Folder view — Select if you want to see folder information on one or two lines. About Chat With IM (network service), you can exchange instant messages with your friends. You can access several chat services or communities simultaneously and switch between them. If you want to, for example, browse the web, you can leave the IM application to run in the background, and still be notified of newinstant messages. The IM application is preinstalled on your device. To start chatting, select Menu > Applications > Chat. Using network services and downloading content to your device may result in data traffic costs. Set up Office Communicator With the Office Communicator application, you can communicate with your colleagues and see their availability. In the home screen, select the Office Communicator set-up shortcut. Define the settings. To later open the application, in the home screen, select the Office Communicator icon. Some services may not be available in all countries, and may be provided only in selected languages. The services may be network dependent. For more information, contact your network service provider. Using the service or downloading content may cause transfer of large amounts of data, which may result in data traffic costs. 49 O u Connectivity CYour device offers several options to connect to the C Internet or to another compatible device or PC. Data connections and access points Your device supports packet data connections (network service), such as GPRS in the GSM network. When you use your device in GSM and UMTS networks, multiple data connections can be active at the same time, and access points can share a data connection. In the UMTS network, data connections remain active during voice calls. You can also use a WLAN data connection. Only one connection in one wireless LAN can be active at a time, but several applications can use the same internet access point. To establish a data connection, an access point is required. You can define different kinds of access points, such as the following: MMS access point to send and receive multimedia messages Internet access point (IAP) to send and receive e-mail and connect to the internet Check the type of access point you need with your service provider for the service you want to access. For availability 50 and subscription to packet data connection services, contact your service provider. Network settings Your device can automatically switch between GSM and 3G networks. The GSM network is indicated with Tin the standby mode. The 3G network is indicated with 3G. Select Menu > Ctrl. panel > Settings and Phone > Network and from the following: Network mode — Select which network to use. If you select Dual mode, the device uses the GSM or 3G network automatically, according to the network parameters and the roaming agreements between the wireless service providers. For details and roaming costs, contact your network service provider. This option is shown only if supported by the wireless service provider. A roaming agreement is an agreement between two or more service providers to enable the users of one service provider to use the services of other service providers. Operator selection — Select Automatic to set the device to search for and select one of the available networks, or Manual to manually select the network from a list. If the connection to the manually selected network is lost, the device sounds an error tone and asks you to reselect a network. The selected network must have a roaming agreement with your home cellular network. Cell info display — Set the device to indicate when it is used in a cellular network based on microcellular network (MCN) technology and to activate cell info reception. Wireless LAN Your device can detect and connect to wireless local area networks (WLAN). Using a WLAN, you can connect your device to the Internet and compatible devices that have WLAN support. About WLAN Your device can detect and connect to wireless local area networks (WLAN). Using a WLAN, you can connect your device to the Internet and compatible devices that support WLAN. To use a WLAN connection, you need the following: WLAN must be available in your location. Your device must be connected to the WLAN. Some WLANs are protected, and you need an access key from the service provider to connect to them. An Internet access point created for WLAN. Use the access pointfor applications that need to connectto the Internet. A WLAN connection is established when you create a data connection using a WLAN internet access point. The active WLAN connection ends when you end the data connection. You can use WLAN during a voice call or when packet data is active. You can only be connected to one WLAN access point device at a time, but several applications can use the same access point. Features that use WLAN, or that are allowed to run in the background while using other features, increase the demand on battery power and reduce the battery life. Your device supports the following WLAN features: IEEE 802.11b/g standard Operation at 2.4 GHz Wired equivalent privacy (WEP), Wi-Fi protected access (WPA/WPA2), and 802.1x authentication methods. These functions can be used only if they are supported by the network. mportant: Always enable one of the available encryption methods to increase the security of your wireless LAN connection. Using encryption reduces the risk of unauthorised access to your data. When the device is in the of line profile, you can still use WLAN, if available. Remember to comply with any applicable safety requirements when establishing and using a WLAN connection. Tip: To check the unique media access control (MAC) address that identifies your device, enter *#62209526# in the home screen. Note: Using WLAN may be restricted in some countries. For example, in France, you are only allowed to use WLAN indoors. For more information, contact your local authorities. 51 WLAN connections To use a wireless LAN (WLAN) connection, you must create an Internet access point (IAP) for WLAN. Use the access point for applications that need to connectto the Internet. A WLAN connection is established when you create a data connection using a WLAN Internet access point. The active WLAN connection ends when you end the data connection. You can use WLAN during a voice call or when packet data is active. You can only be connected to one WLAN access point device at a time, but several applications can use the same Internet access point. When the device is in the offline profile, you can still use WLAN (if available). Remember to comply with any applicable safety requirements when establishing and using a WLAN connection. Tip: To check the unique media access control (MAC) address that identifies your device, enter *#62209526# in the home screen. must enter the correct network name (service set identifier, SSID). If you already have the web browser running using the currently active WLAN connection, to return to the web browser, select Cont.web browsing. To end the active connection, select the connection and Disconnect WLAN. WLAN internet access points Select Menu > Ctrl. panel > Connectivity > WLAN wiz. and Options. Select from the following: Filter WLAN networks — Filter out wireless LANs (WLANs) from the list of found networks. The selected networks are not displayed the next time the application searches for WLANs. Details — View the details of a network shown in the list. If you select an active connection, the connection details are displayed. WLAN wizard o Select Menu > Ctrl. panel > Connectivity > WLAN The WLAN wizard helps you to connect to a wireless LAN (WLAN) and manage your WLAN connections. If the search finds WLANs, to create an Internet access point (IAP) for a connection and start the web browser using this IAP, select the connection and Start web browsing. 52 If you select a secured WLAN, you are asked to enter the relevant password. To connect to a hidden network, you Oneratina modes There are two operating modes in WLAN: infrastructure and ad hoc. The infrastructure operating mode allows two kinds of communication: wireless devices are connected to each other through a WLAN access point device, or wireless devices are connected to a wired LAN through a WLAN access point device. In the ad hoc operating mode, devices can send and receive data directly with each other. WLAN settings SelectMenu > Ctrl. panel > SettingsandConnection > Wireless LAN. To have an indicator displayed when there is a wireless LAN (WLAN) available in your current location, select Show WLAN availability > Yes. To select the interval for your device to scan for available WLANs, and to update the indicator, select Scan for networks. This setting is not available unless you select Show WLAN availability > Yes. To set the device to test the internet capability of the selected WLAN automatically, to ask for permission every time, or to never perform the connectivity test, select > , or . If you select or allow the test to be performed when the device asks for it, and the connectivity test is performed successfully, the access point is saved to internet destinations. To check the unique media access control (MAC) address that identifies your device, enter *#62209526# in the home screen. The MAC address is displayed. Active data connections Select Menu > Ctrl. panel > Connectivity > Conn. mgr.. Select Active data connections. In the active data connections view, you can see the open data connections: # packet data connections (1,T) wireless LAN (WLAN) connections °Note: The actual invoice for calls and services from your service provider may vary, depending on network features, rounding off for billing, taxes, and so forth. To end a connection, select Options > Disconnect. To close all open connections, select Options > Disconnect all. To view the details of a connection, select Options > Details. Sync Select Menu > Ctrl. panel > Phone > Sync. Sync enables you to synchronise your notes, calendar entries, text and multimedia messages, browser bookmarks, or contacts with various compatible applications on a compatible computer or on the internet. You may receive synchronisation settings in a special message from your service provider. A synchronisation profile contains the necessary settings for synchronisation. When you open the Sync application, the default or previously used sync profile is displayed. To modify the profile, scroll to a sync item, and select Mark to include it in the profile or Unmark to leave it out. To manage sync profiles, select Options and the desired option. 53 > To synchronise data, select Options > Synchronise. To ~ cancel synchronisation before it finishes, select Cancel. C Bluetooth connectivity >_ 0 o About Bluetooth connectivity With Bluetooth connectivity, you can make a wireless connection to other compatible devices, such as mobile devices, computers, headsets, and car kits. You can use the connection to send images, video and sound clips, and notes, transfer files from your compatible PC, and print images with a compatible printer. Since devices with Bluetooth wireless technology communicate using radio waves, they do not need to be in direct line-of-sight. However, they must be within 10 metres (33 feet) of each other, although the connection may be subject to interference from obstructions such as walls or from other electronic devices. This device is compliant with Bluetooth Specification 2.0 + EDR supporting the following profiles: Advanced Audio Distribution, Audio Video Remote Control, Basic Imaging, Basic Printing, Dial-up Networking, File Transfer, Generic Access, Hands-free, Headset, Human Interface Device, Object Push, Phone Book Access, SIM Access, Serial Port. To ensure interoperability between other devices supporting Bluetooth technology, use Nokia approved accessories for this model. Check with the manufacturers of other devices 54 to determine their compatibility with this device. Features using Bluetooth technology increase the demand on battery power and reduce the battery life. When the device is locked, only connections to authorised devices are possible. Settings Select Menu > Ctrl. panel > Connectivih > Bluetooth. When you open the application for the first time, you are asked to define a name for your device. You can change the name later. Select from the following: Bluetooth — Turn Bluetooth connectivity on or off. My phone's visibility — To allow your device to be found by other devices with Bluetooth wireless technology, select Shown to a.. To set a time period after which the visibility is set from shown to hidden, select Define period. To hide your device from other devices, select Hidden. My phone's name — Edit the name shown to other devices with Bluetooth wireless technology. Remote SIM mode — Enable or disable another device, such as a compatible car kit accessory, to use the SIM card in your device to connect to the network. Security tips Select Menu > Ctrl. panel > ConnectivitS > Bluetooth. 3. Select the device with which you want to connect. lirp V CI) C C O u When you are not using Bluetooth connectivity, to control who can find your device and connect to it, select Bluetooth > Off or My phone's visibility > Hidden. Operating the device in hidden mode is a safer way to avoid malicious software. Do not accept Bluetooth connectivity from sources you do not trust. Alternatively, switch off the Bluetooth function. This does not affect other functions of the device. Do not pair with or accept connection requests from an unknown device. This protects your device from harmful content. Send data using Bluetooth connectivity Several Bluetooth connections can be active at a time. For example, if you are connected to a compatible headset, you can also transfer files to another compatible device at the same time. Open the application where the item you want to send is stored. Scroll to an item, and select Options > Send > Via Bluetooth. Devices using Bluetooth technology within range are displayed. Device icons are as follows: 0 computer 0 phone () audio or video device 00 other device To interrupt the search, select Cancel. If the other device requires pairing before data can be transmitted, a tone sounds, and you are asked to enter a passcode. The same passcode must be entered in both devices. When the connection is established, Sending data is displayed. Pair deviceF To pair with compatible devices and view your paired devices, in the main view of Bluetooth connectivity, scroll right. Before pairing, create your own passcode (1 to 16 digits), and agree with the owner of the other device to use the same code. Devices that do not have a user interface have a factory-set passcode. The passcode is used only once. To pair with a device, select Options > New paired device. Devices that are within range are displayed. Select the device, and enter the passcode. The same passcode must be entered on the other device as well. Some audio enhancements connect automatically to your device after pairing. Otherwise, scroll to the enhancement, and select Options > Connect to audio device. Paired devices are indicated by i:* in the device search. To set a device as authorised or unauthorised, scroll to the device, and select from the following options: • Set as authorised — Connections between your device and the authorised device can be made without your knowledge. No separate acceptance or 55 authorisation is needed. Use this status for your own devices, such as your compatible headset or PC or devices that belong to someone you trust. Ei indicates authorised devices in the paired devices view. • Set as unauthorised —Connection requests from this device must be accepted separately every time. To cancel a pairing, scroll to the device, and select Options > Delete. If you want to cancel all pairings, select Options > Delete all. Receive data using Bluetooth connectivity When you receive data through Bluetooth connectivity, a tone sounds, and you are asked if you want to accept the message. If you accept, r=lis displayed, and the item is placed in the Inboxfolderin Messaging. Messages received through Bluetooth connectivity are indicated by (f. Tip: If your device notifies you that the memory is full when you try to receive data through Bluetooth connectivity, change memory card as the memory where the data is stored. Scroll to a device you want to block, and select > Block. To unblock a device, open the Blocked devices tab, scroll to a device, and select Options > Delete. To unblock all blocked devices, select Options > Delete If you reject a pairing requestfrom another device, you are asked if you want to block all future connection requests from this device. If you accept the query, the remote device is added to the list of blocked devices. Remote SIM mode Before the remote SIM mode can be activated, the two devices must be paired and the pairing initiated from the other device. When pairing, use a 16-digit passcode, and set the other device as authorised. To use the remote SIM mode with a compatible car kit enhancement, activate Bluetooth connectivity, and enable the use of the remote SIM mode with your device. Activate the remote SIM mode from the other device. When the remote SIM mode is on in your device, SIM mode is displayed in the standby mode. The connection to the wireless network is turned off, as indicated by Xin the signal strength indicator area, and you cannot use SIM card services or features requiring cellular network coverage. When the wireless device is in the remote SIM mode, you can only use a compatible connected enhancement, such as a car kit, to make or receive calls. Your wireless device will not make any calls while in this mode, except to the emergency numbers programmed into your device. To Block devices Select Menu > Ctrl. panel > Connectivity > Bluetooth. To block a device from establishing a Bluetooth 56 connection to your device, open the Paired devices tab. a ~ .; .471 u d C C o u make calls from your device, you must leave the remote SIM mode. If the device is locked, enter the lock code to unlock it. To leave the remote SIM mode, press the power key, and select Exit remote SIM mode. Data cable To avoid corrupting data, do not disconnect the USB data cable during data transfer. Transfer data between your device and a PC Insert a memory card in your device, and connect the device to a compatible PC with the data cable. When the device asks which mode to use, select Mass storage. In this mode, you can see your device as a removable hard drive in your computer. End the connection from the computer (from the Unplug or Eject Hardware wizard in Microsoft Windows, for example) to avoid damaging the memory card. To use Nokia Ovi Suite with your device, install Nokia Ovi Suite on your PC, connect the data cable, and select PC Suite. To synchronise the music in your device with Nokia Ovi Player, install the Nokia Ovi Player software on your PC, connect the data cable, and select Media transfer. To change the USB mode you normally use with the data cable, select Menu > Uri. panel > Connectivity > USB and USB connection mode, and the desired option. To set the device to ask for the mode each time you connect the data cable to the device, select Menu > Ctrl. pane > -innectivity > USB and Ask on connection > Yes. PC connections You can use your mobile device with a variety of compatible PC connectivity and data communications applications. With Nokia Ovi Suite you can, for example, transfer files and images between your device and a compatible computer. To use Ovi Suite with USB connection mode, select PC Suite. For more information about Ovi Suite, see the support area at www.ovi.com. About home network Your device is compatible with Universal Plug and Play (UPnP) and certified by the Digital Living Network Alliance (DLNA). You can use a wireless LAN (WEAN) access point device or router to create a home network. Then you can connect compatible WEAN-enabled UPnP devices to the network. Compatible devices may be your mobile device, a compatible PC, a sound system, a television, or a compatible wireless multimedia receiver connected to a sound system or television. You can share and synchronise media files in your mobile device with other compatible UPnP and DLNA certified devices using the home network. To activate the home 57 network functionality and manage the settings, select Menu > Applications > Home media. You can also use the Home media application to view and play media files from home network devices on your device or on other compatible devices such as a PC, sound system, or television. To viewyour media files on another home network device, in Photos, for example, select a file, Options > Show via home network, and the device. To use the WLAN function of your device in a home network, you must have a working WLAN home connection and have other UPnP enabled home devices connected to the same home network. After setting up your home network, you can share your photos and video clips with your friends and family at home. You are also able to store your media to a media server or retrieve media files from a compatible home server. You can play music stored in your device using a DLNA certified home stereo system, controlling the playlists and volume levels directly from your device. You can also view images captured with the camera of your device on a compatible TV screen, all controlled with your device over WLAN. The home network uses the security settings of the WLAN connection. Use the home network feature in a WLAN infrastructure network with a WLAN access point device and encryption enabled. Your device is connected to the home network only if you accept a connection request from another compatible device, or select the option to view, play, or copy media files on your device or search for other devices. 58 Internet 4 With the Web browser, you can view hypertext markup language (HTML) web pages on the internet as originally designed. You can also browse web pages that are designed specifically for mobile devices, and use extensible hypertext markup language (XHTML), or the wireless markup language (WML). To browse the web, you need to have an internet access point configured in your device. Using the web browser requires network support. Browse the web With the Browser application, you can browse web pages. Select Menu > Internet > Web. OShortcut: To open Browser, press and hold 0 in the home screen. Go to a web page — In the bookmarks view, select a bookmark, or start entering a web address (the g field opens automatically), and select Go to. Some web pages may contain material, such as video clips, that requires a large amount of memory to view. If your device runs out of memory while loading such a web page, insert a memory card. Otherwise, the video clips are not displayed. Disable graphics to save memory and speed up downloading — Select Options > Settings > Page > Load content > Text only. Refresh the content of the web page — Select Options > Web page options > Reload. View snapshots of web pages you have visited — Select Back. A list of pages you have visited during the current browsing session opens. This option is available if History list is activated in the browser settings. Block or allow the automatic opening of multiple windows — Select Options > Web page options > Block pop-ups or Allow pop-ups. View the shortcut keys — Select Options > Keypad shortcuts. To edit the shortcut keys, select Edit. Zoom in or out on a web page — Press * or #. Tip: To go to the home screen without exiting the Browser application or closing the connection, press the end key once. Browser toolba• The browser toolbar helps you select frequently used functions of the browser. Open the toolbar — Press and hold the scroll key on a blank area of a web page. Move within the toolbar — Scroll left or right. Select a feature from the toolbar — Press the scroll key From the toolbar, select from the following: q$ Go to web address — Enter a web address. Recently visited pages — View a list of the web addresses you visit frequently. Bookma __ — Open the bookmarks view. ¿ Full screen — View the web page in full screen. E Page overview — Display an overview of the current web page. Search by keyword — Search the current web page. Settings — Modify the web browser settings. Navigate pages When you are browsing a large web page, you can use Mini Map or Page overview to view the page at one glance. Select Menu > Internet > Web. Activate the Mini Map — Select Options > Settings > General > Mini map > On. When you scroll through a large web page, the Mini Map opens and shows an overview of the page. Move on the Mini Map — Scroll left, right, up, or down. When you find the desired location, stop scrolling. The Mini Map disappears and leaves you at the selected location. Find information on a web page with Page overview 1. Press 8. A miniature image of the current web page 59 opens. d 2. Move on the miniature image by scrolling up, down, C left, or right. 3. When you find a section you want to view, select OKto ++ go to that section on the web page. >_ In1 Search for text within the current web page — Select Options > Find keyword. To go to the previous or next match, scroll up or down. OTip: To search for text within the current web page, press 2. Web feeds and blogs With web feeds, you can easily follow news headlines and your favourite blogs. Select Menu > Internet > Web. Web feeds are XML files on web pages. They are used to share, for example, the latest news headlines or blogs. It is common to find web feeds on web, blog, and wild pages. The browser application automatically detects if a web page contains web feeds. Subscribe to a web feed when a feed is available on the page — Select Options > Subscribe to web feeds. Update a web feed — In the Web feeds view, select a feed and Options > Web feed options > Refresh. Set automatic update for all web feeds — In the Web feeds view, select Options > Edit > Edit. This option is not available if one or more feeds are marked. Content search With keyword search, you can quickly find the information you are looking for on a web page. 60 Select Menu > Internet > Web. Bookmarks You can store your favourite web pages in Bookmarks for instant access. Select Menu > Internet > Web. Access bookmarks If you have a page other than Bookmarks as your homepage, select Options > Go to > Bookmarks. Select a web address from the list or from the collection of bookmarks in the Recently visited pages folder. Save the current web page as a bookmark — While browsing, select Options > Web page options > Save as bookmark. Edit or delete bookmarks — Select Options > Bookmark manager. Send or add a bookmark, or set a bookmarked web page as the homepage — Select Options > Bookmark options. Empty the cache Emptying the cache memory helps you keep your data secure. The information or services you have accessed are stored in the cache memory of the device. If you have accessed or tried to access confidential information requiring passwords, emptythe cache after each browsing session. Select Options > Clear privacy data > Cache. End the connection End the connection and close the Browser application — Select Options > Exit. Delete cookies — Select Options > Clear privacy data > Cookies. Cookies contain information collected about your visits to web pages. Connection security With a secure connection and security certificates, you can safely browse the internet. If the security indicator c8) is displayed during a connection, the data transmission between the device and the internet gateway or server is encrypted. The security icon does not indicate that the data transmission between the gateway and the content server (where the data is stored) is secure. The service provider secures the data transmission between the gateway and the content server. Security certificates may be required for some services, such as banking services. You are notified if the identity of the server is not authentic or if you do not have the correct security certificate in your device. For more information, contact your service provider. mportant: Even if the use of certificates makes the risks involved in remote connections and software installation considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted certificates for increased security to be available. Certificates have a restricted lifetime. If "Expired certificate" or "Certificate not valid yet" is shown, even if the certificate should be valid, check that the current date and time in your device are correct. Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that the certificate really belongs to the listed owner. Wea settings Select Menu > Internet > Web and Options > Settings and from the following: General settings Access point — Change the default access point. Some or all access points may be preset for your device by your service provider. You may not be able to change, create, edit, or remove them. Homepage — Define the homepage. Mini map — Turn Mini Map on or off. Mini Map helps with web page navigation. History list — If you select On, while browsing, to see a list of the pages you have visited during the current session, select Back. 61 Web address suffix — Enter a web address suffix that the device uses by default when you enter a web address in the Go to field (for example, .com or .org). Security warnings — Hide or show security notifications. Java/ECMA script — Enable or disable the use of scripts. Java/ECMA script errors — Select whether you want to receive script notifications. Page settings Load content — Select whether you want to load images and other objects while browsing. If you select Text only, to load images or objects later during browsing, select Options > Display options > Load images. Default encoding — If text characters are not shown correctly, you can select another encoding according to the language for the current page. Imo. — Allow or block automatic opening of different pop-ups while browsing. Automatic reload —Selectwhether you wanttheweb pages to be refreshed automatically while browsing. Nokia Office Tools Nokia Office Tools support mobile business and enable effective communication with work teams. Font size — Define the font size that is used for web pages. Privacy settings Recently visited pages — Enable or disable automatic bookmarkcollecting. If you wantto continue saving the addresses of the visited web pages into the Recently visited pages folder, but hide the folder from the bookmarks view, select Hide folder. Form data saving — Select whether you want the password data or data you enter on different forms on a web page to be saved and used the next time you open the page. — Enable or disable the receiving and sending of cookies. Web feed settings Acc. point for auto-update — Select the desired access point for updating. This option is only available when Automatic updates is active. Update when roaming — Select whether you want the web feeds to be updated automatically when roaming. Active notes IU Select Menu > Office > Active notes. 62 Nokia Office Tools Active notes allows you to create, edit, and view different kinds of notes, for example, meeting memos, hobby notes, or shopping lists. You can insert images, videos, and sound in the notes. You can link notes to other applications, such as Contacts, and send notes to others. Create and edit 'mica Select Menu > Office > Active notes. To create a note, start writing. To edit a note, select the note and Options > Editing options. To add boldface, italics, or underlining to your text or change the font colour, press and hold the Shift key, and scroll to select the text. Then select Options > Text. Select Options and from the following: Insert object — Insert images, sound or video clips, business cards, web bookmarks, and files. Insert new — Add new items to the note. You can record sound and video clips, and capture images. Send — Send the note. Link note to call — Select "" `^^*- is to link a note to a contact. The note is displayed when making a call to or receiving a call from the contact. Settings for Active notes Select Menu > Office > Active notes and Options > Settings. To select where to save notes, select Memory in use and the desired memory. To change the layout of active notes, or to view the notes as a list, select Change view > Grid or List. To see a note in the background when making or receiving phone calls, select Show note during call > Yes. Tip: If you temporarily do not want to see notes during phone calls, select Show note during call > No. This way you do not have to remove the links between notes and contact cards. Calculator Select Menu > Office > Calculator. This calculator has limited accuracy and is designed for simple calculations. To make a calculation, enter the first number of the calculation. Select a function such as add or subtract from the function map. Enter the second number of the calculation, and select =. The calculator performs operations in the order they are entered. The result of the calculation remains in the editor field and can be used as the first number of a new calculation. The device saves the result of the last calculation in its memory. Exiting the Calculator application or switching off the device does not clear the memory. To recall the last saved result the next time you open the Calculator application, select Options > Last result. To save the numbers or results of a calculation, select Options > Memory > Save. To retrieve the results of a calculation from the memory and use them in a calculation, select Options > Memory > Recall. 63 Nokia Office Tools File manager in About File manager Select Menu > Office > File mgr.. With File manager, you can browse, manage, and open files. The available options may vary. To map or delete drives, or to define settings for a compatible remote drive connected to your device, select Options > Remote drives. Find and organise files Select Menu > Office > File mgr.. To find a file, select Options > Find. Select where to search, and enter a search term that matches the file name. To move or copy files and folders, or to create new folders, select Options > Organise. Manage a memory card Select Menu > Office > File mgr.. These options are available only if a compatible memory card is inserted in the device. Select Options and from the following: Memory card options — Rename or format a memory 64 card. Memory card password — Password protect a memory card. Unlock memory card — Unlock a memory card. Back up files to a memory card Select Menu > Office > File mgr.. To back up files to a memory card, select the file types you want to back up, and Options > Back up phone memory. Ensure that your memory card has enough free memory for the files that you have chosen to back up. Quickoffice j About Quickoffice Select Menu > Office > Quickoffice. Quickoffice consists of Quickword for viewing Microsoft Word documents, Quicksheet for viewing Microsoft Excel worksheets, Quickpoint for Microsoft PowerPoint presentations, and Quickmanager for purchasing software. You can view Microsoft Office 2000, XP, 2003, and 2007 documents (DOC, XLS, and PPT file formats) with Quickoffice. If you have the editor version of Quickoffice, you can also edit files. Not all file formats or features are supported. Converter Select Menu > Office > Converter. The converter has limited accuracy, and rounding errors may occur. Convert measurements Select Menu > Office > Converter. Scroll to the type field, and select Options > Conversion type to open a list of measures. Select the measurement type to use (other than currency) and OK. Scroll to the first unit field, and select Option > Select unit. Select the unit from which to convert and OK. Scroll to the next unit field, and select the unit to which to convert. Scroll to the first amount field, and enter the value to convert. The other amountfield changes automatically to show the converted value. Set base currency and exchange rate Select Menu > Office > Converter. When you change base currency, you must enter new exchange rates because all previously set exchange rates are cleared. Before you can make currency conversions, you must choose a base currency and add exchange rates. The rate of the base currency is always 1. The base currency determines the conversion rates of the other currencies. To set the exchange rate for the unit of currency, scroll to the type field, and select Options > Currency rates. Scroll to the currencytype, and enter the exchange rate you would like to set per single unit of currency. To change the base currency, scroll to the currency, and select Options > Set as base currency. Select Done > Yes to save the changes. After you have set all the necessary exchange rates, you can make currency conversions. Zip manager q Select Menu > Office > Zip. With Zip manager, you can create new archive files to store compressed ZIP formatted files; add single or multiple compressed files or directories to an archive; set, clear, or change the archive password for protected archives; and change settings, such as compression level, and file name encoding. You can save the archive files in the device memory or on a memory card. PDF reader I Select Menu > Office > Adobe PDF. With PDF reader, you can read PDF documents on the display of your device; search for text in the documents; modify settings, such as zoom level and page views; and send PDF files using e-mail. 65 Nokia Office Tools Printing You can print documents, such as files, messages, images, or web pages, from your device. You may not be able to print all types of documents. File printing Print files Select Menu > Ctrl. panel > Printers. Before printing, ensure that all the necessary configurations have been done to connect your device to the printer. Select Options > Printing options and from the following: Print — Print a document. To printto a file, select to file, and define the location for the file. Page setup — You can change the paper size and orientation, define the margins, and insert a header or a footer. The maximum length of the header and footer is 128 characters. Preview — Preview the document before printing. Printing options Open a document, such as a file or message, and select Options > Printing options > Print. Define the following options: Printer — Select an available printer from the list. Print — Select All pages, Even pages, or Odd pages 66 as the print range. Print range — Select All pages in range, Current page, or Defined pages as the page range. Number of copies — Select the number of copies to print. Print to file — Select to print to a file and determine the location for the file. The available options may vary. Printer settings Select Menu > Ctrl. panel > Printers. To add a new printer, select Options > Add. Define the following: Printer — Enter a name for the printer. Driver — Select a driver for the printer. Bearer — Select a bearer for the printer. Access point — Select the access point. Port — Select the port. Host — Define the host. User — Enter the user. Queue — Enter the print queue. Orientation — Select the orientation. Paper size — Select the paper size. Media type — Select the media type. Colour mode — Select the colour mode. Printer model — Select the printer model. The available options may vary. Image print You can print images from your device using a printer compatible with PictBridge. You can only printimages that are in the JPEG file format. To print images in Photos, camera, or image viewer, mark the images, and select Options > Print. Connect to printer Connect your device to a compatible printer with a compatible data cable, and select Image transfer as the USB connection mode. To set your device to ask the purpose of the connection each time the cable is connected, select Menu > Ctrl. panel and Connectivity > USB > Ask on connection > Yes. Print preview After you select the printer, the selected images are displayed using predefined layouts. If the images do not fit on a single page, scroll up or down to display the additional pages. Image print view After you selectthe images to print and the printer, define the printer settings. Select from the following: Layout — Select the layout for the images. Paper size — Select the paper size. Print quality — Select the print quality. Dictionary Select Menu > Office > Dictionary. To translate words from one language to another, enter text in the search field. As you enter text, suggestions of words to translate are displayed. To translate a word, select the word from the list. All languages may not be supported. Select Options and from the following: Listen — Listen to the selected word. History — Find previously translated words from the current session. Languages — Change the source or target language, download languages from the internet, or remove a language from the dictionary. You cannot remove the English language from the dictionary. You can have two additional languages installed, besides English. Speech — Edit the voice feature settings. You can adjust the speed and volume of the voice. Notes Select Menu > Office > . You can create and send notes to other compatible devices, and save received plain text files (TXT file format) to Notes. To write a note, start entering the text. The note editor opens automatically. To open a note, select Open. To send a note to other compatible devices, select Options > Send. To synchronise or to define synchronisation settings for a note, select Options > Synchronisation. Select Start to initialise synchronisation or Settings to define the synchronisation settings for the note. 67 Positioning (GPS) 68 Positioning (GPS) L"4 You can use applications such as GPS data to find out your location or measure distances. These applications require a GPS connection. About GPS The coordinates in the GPS are expressed using the international WGS-84 coordinate system. The availability of the coordinates may vary by region. The Global Positioning System (GPS) is operated by the government of the United States, which is solely responsible for its accuracy and maintenance. The accuracy of location data can be affected by adjustments to GPS satellites made by the United States government and is subject to change with the United States Department of Defense civil GPS policy and the Federal Radionavigation Plan. Accuracy can also be affected by poor satellite geometry. Availability and quality of GPS signals may be affected by your location, buildings, natural obstacles, and weather conditions. GPS signals may not be available inside buildings or underground and may be impaired by materials such as concrete and metal. GPS should not be used for precise location measurement, and you should never rely solely on location data from the GPS receiver and cellular radio networks for positioning or navigation. The trip meter has limited accuracy, and rounding errors may occur. Accuracy can also be affected by availability and quality of GPS signals. Different positioning methods can be enabled or disabled in positioning settings. Assisted GPS (A-GPS) Your device also supports assisted GPS (A-GPS). A-GPS requires network support. Assisted GPS (A-GPS) is used to retrieve assistance data over a packet data connection, which assists in calculating the coordinates of your current location when your device is receiving signals from satellites. When you activate A-GPS, your device receives useful satellite information from an assistance data server over the cellular network. With the help of assisted data, your device can obtain the GPS position faster. Your device is preconfigured to use the Nokia A-GPS service, if no service provider-specific A-GPS settings are available. The assistance data is retrieved from the Nokia A-GPS service server only when needed. To disable the A-GPS service, select Menu > Applications > GPS data and Options > Positioning Positioning (GPS) settings > Positioning methods > Assisted GPS > Options > Disable. You must have an Internet access point defined in the device to retrieve assistance data from the Nokia A-GPS service over a packet data connection. The access point for A-GPS can be defined in positioning settings. A wireless LAN (WLAN) access point cannot be used for this service. Only a packet data Internet access point can be used. Your device asks you to select the Internet access point when GPS is used for the first time. Hold your device correctly When using the GPS receiver, ensure you do not cover the antenna with your hand. Establishing a GPS connection may take from a Í couple of seconds to several minutes. Establishing a GPS connection in a vehicle may take longer. The GPS receiver draws its power from the device battery. Using the GPS receiver may drain the battery faster. J Tips on creating a GPS connection If your device cannot find the satellite signal, consider the following: If you are indoors, go outdoors to receive a better signal. If you are outdoors, move to a more open space. Ensure that your hand does not cover the GPS antenna of your device. If the weather conditions are bad, the signal strength may be affected. Some vehicles have tinted (athermic) windows, which may block the satellite signals. Check satellite signal status To check how many satellites your device has found, and whether your device is receiving satellite signals, select Menu > Applications > GPS data and Options > Satellite status. If your device has found satellites, a bar for each satellite is displayed in the satellite information view. The longer the bar, the stronger the satellite signal is. When your device has received enough data from the satellite signal to calculate the coordinates of your location, the bar colour changes. Initially, your device must receive signals from at least four satellites to be able to calculate the coordinates of your location. When the initial calculation has been made, it may be possible to continue calculating the coordinates of your location with three satellites. However, the accuracy is generally better when more satellites are found. Signal strengths: Chg view Close 69 Positioning (GPS) Position requests You may receive a request from a network service to receive your position information. Service providers may offer information about local topics, such as weather or traffic conditions, based on the location of your device. When you receive a position request, the service that is making the request is displayed. Select Accept to allow your position information to be sent or Reject to deny the request. Landmarks With Landmarks, you can save the position information of specific locations in your device. You can sort the saved locations into different categories, such as business, and add other information to them, such as addresses. You can use your saved landmarksin compatible applications, such as GPS data. Select Menu > Applications > Landmarks. The coordinates in the GPS are expressed using the international WGS-84 coordinate system. Select Options and from the following: New landmark — Create a new landmark. To make a positioning request for your current location, select Current position. To select the location from the map, select Select from map. To enter the position information manually, select Enter manually. Edit — Edit or add information to a saved landmark 70 (for example, a street address). Add to category — Add a landmark to a category in Landmarks. Select each category to which you want to add the landmark. Send — Send one or several landmarks to a compatible device. Your received landmarks are placed in the Inbox folder in Messaging. You can sort your landmarks into preset categories, and create new categories. To edit and create new landmark categories, open the categories tab, and select Options > Edit categories. GPS data Route guidance Select Menu > Applications > GPS data and Navigation. Start the route guidance outdoors. If started indoors, the GPS receiver may not receive the necessary information from the satellites. Route guidance uses a rotating compass on the device display. A red ball shows the direction to the destination, and the approximate distance to it is shown inside the compass ring. Route guidance is designed to show the straightest route and the shortest distance to the destination, measured in a straight line. Any obstacles on the route, such as buildings and natural obstacles, are ignored. Differences in altitude are nottaken into accountwhen calculating the distance. Route guidance is active only when you move. To set your trip destination, select Options > Set destination and a landmark as the destination, or enter the latitude and longitude coordinates. To clear the destination set for your trip, select Stop navigation. Trip meter Select Menu > Applications > GPS data and T distance. The trip meter has limited accuracy, and rounding errors may occur. Accuracy can also be affected by availability and quality of GPS signals. To turn trip distance calculation on or off, select Start or Stop. The calculated values remain on the display. Use this feature outdoors to receive a better GPS signal. To set the trip distance and time and average and maximum speeds to zero, and to start a new calculation, select Options > Reset. To set the trip meter and total time to zero, select Restart. Positioning settings Select Menu > Ctrl. panel > Settings and General > Positioning. Positioning methods Select from the following: Integrated GPS — Use the integrated GPS receiver of your device. Assisted GPS — Use Assisted GPS (A-GPS) to receive assistance data from an assistance data server. Bluetooth GPS — Use a compatible external GPS receiver with Bluetooth connectivity. Network based — Use information from the cellular network (network service). Positioning server To define an access point and positioning server for network-assisted positioning methods, such as assisted GPS or network-based positioning, select Positioning . The positioning server may be preset by your service provider, and you may not be able to edit the settings. Notation settings To select which measurement system you want to use for speeds and distances, select Measurement system > Metric or Imperial. To define in which format the coordinate information is displayed in your device, select Coordinate format and the desired format. ~ Maps 71 ro Maps overview E eSelect Menu > Maps. Welcome to Maps. Maps shows you whatis nearby, helps you plan your route, and guides you where you want to go. Find cities, streets, and services. Find your way with turn-by-turn directions. Synchronise your favourite locations and routes between your mobile device and the Ovi Maps internet service. Check weather forecasts and other local information, if available. , Note: Downloading content such as maps, satellite images, voice files, guides or traffic information may involve transmission of large amounts of data (network service). Some services may not be available in all countries, and may be provided only in selected languages. The services may be network dependent. For more information, contact your network service provider. Almost all digital cartography is inaccurate and incomplete to some extent. Never rely solely on the cartography that you download for use in this device. Content such as satellite images, guides, weather and traffic information and related services are generated by third parties independent of Nokia. The content may be 72 inaccurate and incomplete to some extent and is subject to availability. Never rely solely on the aforementioned content and related services. My position View your location and the map See your current location on the map, and browse maps of different cities and countries. Select Menu > Maps and My position. When the GPS connection is active, • marks your current or last known location on the map. If the icon's colours are faint, no GPS signal is available. If only cell ID based positioning is available, a red halo around the positioning icon indicates the general area you might be in. The accuracy of the estimate increases in densely populated areas. Move on the map — Use the scroll key. By default, the map is oriented north. View your current or last known location — Press O. Zoom in or out — Press * or #. If you browse to an area not covered by maps that are stored on your device and you have an active data connection, new maps are automatically downloaded. Map coverage varies by country and region. Map view Parliament Square Soft London. United Kingdom Q4~ J ,ill Cabinet Walr lawoarlesRoor 1 I e113í - 1— Selected location 2 — Indicator area 3 — Point of interest (for example, a railway station or a museum) 4 — Information area Change the look of the map View the map in different modes, to easily identify where you are. Select Menu > Maps and My position. Press 1, and select from the following: Map — In the standard map view, details such as location names or motorway numbers, are easyto read. Satellite — For a detailed view, use satellite images. Terrain — View at a glance the ground type, for example, when you are travelling off-road. Change between 2D and 3D views — Press 3. Download and update map_ To avoid mobile data transfer costs, download the latest maps and voice guidance files to your computer, and then transfer and save them to your device. Use the Nokia Ovi Suite application to download the latest maps and voice guidance files to your compatible computer. To download and install Nokia Ovi Suite on your compatible computer, go to www.ovi.com. Tip: Save new maps to your device before a journey, so you can browse the maps without an internet connection when travelling abroad. To make sure your device does not use an internet connection, in the main menu, select Options > Settings > Internet > Connection > Offline. Use the compass When the compass is activated, both the arrow of the compass and the map rotate automatically in the direction to which the top of your device is pointing. Select Menu > Maps and My position. Activate the compass — Press 5. Deactivate the compass — Press 5 again. The map is oriented north. The compass is active when there is a green outline. If the compass needs calibration, the outline of the compass is around all axes in a continuous movement. red or yellow. To calibrate the compass, rotate the device 73 3 2 a ~ The compass has limited accuracy. Electromagnetic fields, metal objects, or other external circumstances may also affect the accuracy of the compass. The compass should always be properly calibrated. About positioning method, Maps displays your location on the map using GPS, A-GPS, or cell ID based positioning. The Global Positioning System (GPS) is a satellite-based navigation system used for calculating your location. Assisted GPS (A-GPS) is a network service that sends you GPS data, improving the speed and accuracy of the positioning. When you use Maps for the first time, you are prompted to define an internet access point to download map information or use A-GPS. indicates the availability of the satellite signals. One bar is one satellite. When the device is searching for satellite signals, the bar is yellow. When there is enough data available to calculate your location, the bar turns green. The more green bars, the more 74 reliable the location calculation. The Global Positioning System (GPS) is operated by the government of the United States, which is solely responsible for its accuracy and maintenance. The accuracy of location data can be affected by adjustments to GPS satellites made by the United States government and is subject to change with the United States Department of Defense civil GPS policy and the Federal Radionavigation Plan. Accuracy can also be affected by poor satellite geometry. Availability and quality of GPS signals may be affected by your location, buildings, natural obstacles, and weather conditions. GPS signals may not be available inside buildings or underground and may be impaired by materials such as concrete and metal. GPS should not be used for precise location measurement, and you should never rely solely on location data from the GPS receiver and cellular radio networks for positioning or navigation. The trip meter has limited accuracy, and rounding errors may occur. Accuracy can also be affected by availability and quality of GPS signals. With cell ID based positioning, the position is determined through the antenna tower your mobile device is currently connected to. Depending on the available positioning method, the accuracy of positioning may vary from a few metres to several kilometres. Find places Find a location Maps helps you find specific locations and types of business you are looking for. l 11111 Select Menu > Maps and Find places. Enter search terms, such as a street address or postcode. To clear the search field, select Clear. Select Go. In the list of proposed matches, go to the desired item. To display the location on the map, select Map. To view the other locations of the search result list on the map, scroll up and down with the scroll key. Return to the list of proposed matches — Select List. Search for different types of nearby places — Select Browse categories and a category, such as shopping, accommodation, or transport If no search results are found, ensure the spelling of your search terms is correct. Problems with your internet connection may also affect results when searching online. To avoid data transfer costs, you can also get search results without an active Internet connection, if you have maps of the searched area stored on your device. View location details View more information about a specific location or place, such as a hotel or restaurant, if available. Select Menu > Maps and My position. View the details of a place — Select a place, press the scroll key, and select Show details. Manage places and routes Save places and routes Save addresses, places of interest, and routes, so they can be quickly used later. Select Menu > Maps. Save a place Select My position. Go to the location. To search for an address or place, select Search. Press the scroll key. Select Save place. Save a route Select My position. Go to the location. To search for an address or place, select Search. To add another route point, press the scroll key, and select Add to route. Select Add new route point and the appropriate option. Select Show route > Options > Save route. View your saved places and routes — Select Favourites > Places or Routes. 75 0 View and organise places or E routes Use your Favourites to quickly access the places and routes you have saved. Group the places and routes into a collection, for example, when planning a trip. Select Menu > Maps and Favourites. View a saved place on the map Select Places. Go to the place. Select Map. To return to the list of saved places, select List. Create a collection — Select Create new collection, and enter a collection name. Add a saved place to a collection Select Places and the place. Select Organise collections. Select New collection or an existing collection. If you need to delete places or routes, or add a route to a collection, go to the Ovi Maps internet service at www.ovi.com. Send places to your friends When you want to share place information with your friends, send these details directly to their devices. 76 Select Menu > Maps and My position Send a place to your friend's compatible device — Select a location, press the scroll key, and select Send. Synchronise your Favourites Plan a trip on your computer at the Ovi Maps website, synchronise the saved places, routes, and collections with your mobile device, and access the plan on the go. To synchronise places, routes, or collections between your mobile device and the Ovi Maps internet service, you need a Nokia account. If you do not have one, in the main view, select Options > Account > Nokia account > Create new account. Synchronise saved places, routes, and collections — Select Favourites > Synchronise with Ovi. If you do not have a Nokia account, you are prompted to create one. Set the device to synchronise Favourites automatically — Select Options > Settings > Synchronisation > Change > At start-up and shut-d.. Synchronising requires an active internet connection, and may involve the transmission of large amounts of data through your service provider's network. Contact your service provider for information about data transmission charges. To use the Ovi Maps internet service, go to www.ovi.com. H CI. Ni E Share location Publish your current location to Facebook, together with text and a picture. Your Facebook friends can see your location on a map. Select Menu > Maps and Share location. To share your location, you need a Nokia account and a Facebook account. Sign in to your Nokia account, or, if you do not yet have one, select Create new account. Sign in to your Facebook account. Select your current location. Enter your status update. To attach a picture to your post, select Add a photo. Select Share location. Manage your Facebook account — In the main view, select Options > Account > Share location settings > Facebook. Sharing your location and viewing the location of others requires an internet connection. This may involve the transmission of large amounts of data and related data traffic costs. The Facebook terms of use apply to sharing your location on Facebook. Familiarise yourself with the Facebook terms of use and the privacy practices. Before sharing your location to others, always consider carefully with whom you are sharing it. Check the privacy settings of the social networking service you are using as you might share your location with a large group of people. Drive and Walk Get voice guidance Voice guidance, if available for your language, helps you find your way to a destination, leaving you free to enjoy the journey. Select Menu > Maps and Drive or Walk. When you use drive or walk navigation for the first time, you are asked to select the language of the voice guidance, and download the appropriate files. If you select a language that includes street names, also the street names are said aloud. Voice guidance may not be available for your language. Change the voice guidance language — In the main view, select Options > Settings > Navigation > Drive guidance or Walk guidance and the appropriate option. Repeat the voice guidance for car navigation — In the navigation view, select Options > Repeat. Adjust the volume of the voice guidance for car navigation — In the navigation view, select Options > Volume. Drive to your destination When you need turn-by-turn directions while driving, Maps helps you get to your destination. Select Menu > Maps and Drive. Drive to a destination — Select Set destination and the appropriate option. 77 a ro f Drive to your home — Select Drive home. When you select Drive home or Walk home for the first time, you are prompted to define your home location. To later change the home location, do the following: In the main view, select Options > Settings > Navigation > Home Location > Change > Redefine. Select the appropriate option. OTip: To drive without a set destination, select Map. Your location is displayed on the centre of the map as you move. Change views during navigation — Press the scroll key, and select 2D view, 3D view, Arrow view, or Route overview. Obey all local laws. Always keep your hands free to operate the vehicle while driving. Your first consideration while driving should be road safety. Navigation view 1 3 2 4 1- Route 2 — Your location and direction 3 — Compass 4 — Information bar (speed, distance, time) Get traffic and safety information Enhance your driving experience with real-time information about traffic events, lane assistance, and speed limit warnings, if available for your country or region. Select Menu > Maps and Drive. 1111 P r o 'c o.o if9 • ® 2,Okm 95km/h 120km 01: 5 78 View traffic events on the map — During drive navigation, select Options > Traffic info. The events are displayed as triangles and lines. Update traffic information — Select Options > Traffic info > Update traffic info. When planning a route, you can set the device to avoid traffic events, such as traffic jams or roadworks. Avoid traffic events — In the main view, select Options > Settings > Navigation > Reroute due to traffic. The location of speed cameras may be shown on your route during navigation, if this feature is enabled. Some jurisdictions prohibit or regulate the use of speed camera location data. Nokia is not responsible for the accuracy, or the consequences of using speed camera location data. Walk to your destination When you need directions to follow a route on foot, Maps guides you over squares, and through parks, pedestrian zones, and even shopping centres. Select Menu > Maps and Walk. Walk to a destination — Select Set destination and the appropriate option. Walk to your home — Select Walk home. When you select Drive home or Walk home for the first time, you are prompted to define your home location. To later change the home location, do the following: 1. In the main view, select Options > Settings > Navigation > Home Location > Change > Redefine. 2. Select the appropriate option. Tip: To walk without a set destination, select Map. Your location is displayed on the centre of the map as you move. in a to E Plan a route Plan your journey, and create your route and view it on the map before setting off. Select Menu > Maps and My position. Create a route Go to your starting point Press the scroll key, and select Add to route. To add another route point, select Add new route point and the appropriate option. Change the order of the route points Go to a route point. Press the scroll key, and select Move. Go to the place where you want to move the route point to, and select OK. Edit the location of a route point — Go to the route point, press the scroll key, and select Edit and the appropriate option. View the route on the map — Select Show route. Navigate to the destination — Select Show route > Options > Start driving or Start walking. Change the settings for a route The route settings affect the navigation guidance and the 79 way the route is displayed on the map. ul C. ra X In the route planner view, open the Settings tab. To get to the route planner view from the navigation view, select Options > Route points or Route point list. Set the transportation mode to Drive or Walk. If you select Walk, one-way streets are regarded as normal streets, and walkways and routes through, for example, parks and shopping centres, can be used. Select the desired option. Select the walking mode — Open the Settings tab, and select Walk > Preferred route > Streets or Straight line. Straight line is useful on off-road terrain as it indicates the walking direction. Use the faster or shorter driving route — Open the Settings tab, and select Drive > Route selection > Faster route or Shorter route. Use the optimised driving route — Open the Settings tab, and select Drive > Route selection > Optimised. The optimised driving route combines the advantages of both the shorter and the faster routes. You can also choose to allow or avoid using, for example, motorways, toll roads, or ferries. Maps shortcuts General shortcuts To zoom in or out on the map, press * or #. To return to your current location, press O. To change the map type, press 1. To tilt the map, press 2 or 8. To rotate the map, press 4 or 6. To return the map back to the north up position, press 5. Pedestrian navigation shortcuts To save a location, press 2. To search for locations by categories, press 3. To adjust the volume of the pedestrian navigation guidance, press 6. To view the list of route points, press 7. To adjust the map for night-time usage, press 8. To view the dashboard, press 9. Car navigation shortcuts To adjust the map for daytime or night-time usage, press 1. To save the current location, press 2. To search for locations by categories, press 3. To repeat the voice guidance, press 4. To find a different route, press 5. To adjust the volume of voice guidance, press 6. To add a stopover to the route, press 7. To view traffic information, press 8. To view the dashboard, press 9. 80 Personalisation You can personalise your device by, for example, adjusting the various tones, background images, and screen savers. Profiles I Select Menu > Ctrl. panel > Profiles. You can adjust and customise the ringing tones, alert tones, and other device tones for different events, environments, or caller groups. The active profile is shown at the top of the display in the home screen. However, if the active profile is General, only today's date is shown. To create a new profile, select Options > Create new, and define the settings. To customise a profile, select a profile and Options > Personalise. To activate a profile, select a profile and Options > Activate. To set the profile to be active until a certain time within the next 24 hours, scroll to the profile, select Options > Timed, and set the time. When the time expires, the profile changes back to the previously active non-timed profile. When the profile is timed, Q is displayed in the home screen. The Offline profile cannot be timed. To delete a profile that you created, select Options > Delete profile. You cannot delete the predefined profiles. When the Offline profile is activated, your connection to the cellular network is closed. All radio frequency signals between the device and the cellular network are prevented. If you try to send a message, it is placed in the Outbox folder, and is sent only when another profile is activated. You can also use your device without a SIM card. If you remove the SIM card, the Offline profile is activated. em °Important: In the Offline profile you cannot make or receive any calls, or use other features that require cellular network coverage. Calls may still be possible to the official emergency number programmed into your device. To make calls, you must first activate the phone function by changing profiles. If the device has been locked, enter the lock code. When you use the Offline profile, you can still use a wireless LAN (WLAN), for example, to read your mail or browse the internet. You can also use Bluetooth connectivity. Remember to comply with any applicable safety requirements when you establish and use WLAN or Bluetooth connections. 81 Select ringing tones HTo set a ringing tone for a profile, select Options > Personalise > Ringing tone. Select a ringing tone from fa the list, or select Download sounds to open a bookmark folder containing a list of bookmarks for downloading tones using the browser. Any downloaded tones are saved to Gallery. a To play the ringing tone for a selected contact group only, select Options > Personalise > Alert for, and select the desired group. Phone calls coming from outside that group have a silent alert. To change the message tone, select Options > Personalise > Message alert tone. Customise profiles Select Menu > Ctrl. panel > Profiles. Select Options > Personalise and from the following: Ringing tone — Select a ringing tone from the list, or select Download sounds to open a bookmark folder containing a list of bookmarks for downloading tones using the browser. If you have two alternate phone lines in use, you can specify a ringing tone for each line. Video call tone — Select a ringing tone for video calls. Say caller's name — When you select this option and someone from your contacts list calls you, the device sounds a ringing tone that is a combination of the spoken name of the contact and the selected ringing 82 tone. 2 Ringing type — Select how you want the ringing tone to alert. Ringing volume — Select the volume level of the ringing tone. Message alert tone — Select a tone for received text messages. E-mail alert tone — Select a tone for received e-mail messages. Vibrating alert — Set the device to vibrate when you receive a call or message. Keypad tones — Select the volume level of the keypad tones. Warning tones — Deactivate the warning tones. This setting also affects the tones of some games and Java"' applications. Alert for — Set the device to ring only upon calls from phone numbers that belong to a selected contact group. Phone calls coming from outside that group have a silent alert. PTT call alerttone — Select a ringing tone for PTT calls. Push to talk status — Set the PTT status to each profile. Profile name — You can give a name to a new profile or rename an existing profile. The General and Offline profiles cannot be renamed. Personalise the home screen Select Menu > ctrl. panel > Modes. To change the name of the current home screen, select Options > Rename mode. To select which applications and notifications you want to see in the home screen, select Home screen applications. To change the theme of the home screen currently in use, select General theme. To change the background image of the home screen currently in use, select Wallpaper. To change from one home screen to another, scroll to Current mode, and select Options > Change. Change the display theme 0 Select Menu > Ctrl. panel > Themes. Select from the following: General — Change the theme used in all applications. Menu view — Change the theme used in the main menu. Standby — Change the theme used in the home screen. Wallpaper — Change the background image of the home screen. Power saver — Select an animation for the power saver. Call image — Change the image displayed during calls. To activate or deactivate the theme effects, select General > Options > Theme effects. Download a theme Select Menu > Ctrl. panel > Themes. To download a theme, select General > Download themes > Options > Go to > New web page. Enter the web address from which you want to download your theme. Once the theme is downloaded, you can preview or activate the theme. To preview a theme, select Options > Preview. To activate a theme, select Options > Set. Change audio themes Select Menu > Ctrl. panel > Themes and Audio themes. You can set sounds for various device events. The sounds can be tones, speech, or a combination of both. To change the current audio theme, select Active audio theme. To set a sound for an event, select an event group, such as ringing tones, and the desired event. To use all the preset sounds in an event group, select the group and Options > Activate sounds. Select Options and from the following: Play voice — Play the sound before activating it. Save theme — Create a new audio theme. 3-D ringing tones — Add 3-D effects to the audio theme. 83 ra ß d f Speech — Select Speech to set speech as the sound for an event. Enter the desired text to the text field. The Speech option is not available if you have activated the Say caller's name option in the current profile. Deactivate sounds — Silence all the sounds in an event group. 3-D ringing tones ,k Select Menu > Ctrl. panel > 3-D tones. To enable three-dimensional (3-D) sound effects for ringing tones, select 3-D ringing tone effects > On. Not all ringing tones support 3-D effects. To change the 3-D effect that is applied to the ringing tone, select and the desired effect. To modify the 3-D effect, select from the following: Trajectory speed — Select the speed at which sound moves from one direction to another. This setting is not available for all effects. Reverberation — Select the desired effect to adjust the amount of echo. Doppler effect — Select On to set the ringing tone sound higher when you are closer to your device, and lower when you are farther away. This setting is not available for all effects. To listen to the ringing tone with the 3-D effect, select Options > Play tone. To adjust the volume of the ringing tone, select Menu > Ctrl. panel > Profiles and Options > Personalise > Ringing volume. Media Your device contains a variety of media applications for both business and leisure time use. Camera Select Menu > Media > Camera. 84 Capture an image Select Menu > Media > Camera. Your device supports an image capture resolution of 2592x1944 pixels. The image resolution in this guide may appear different. Use the display as a viewfinder. To zoom in or out before capturing an image, use the volume keys. If the Optical Navi key is activated, to — autofocus, hold your finger on the scroll key. To capture the image, press the scroll key. If the Optical Navi key is deactivated, to autofocus, press and hold the scroll key. To capture the image, release the scroll key. The device saves the image in Photos. See "Optical Navi key". D. 24. The toolbar provides you with shortcuts to different items and settings before and after capturing an image or recording a video clip. Select from the following: In Switch to image mode. 13 Switch to video mode. Select the scene. Switch to panorama mode. Switch the video light off (video mode only) Switch the video light on (video mode only) Select the flash mode (images only). Activate the self-timer (images only). Activate sequence mode (images only). Select a colour tone. ra Adjust the white balance. The available options vary depending on the mode and view you are in. The settings return to the default values when you close the camera. To customise the camera toolbar, switch to image mode, and select Options > Customise toolbar. Scenes Select Menu > Media > Camera. A scene helps you to find the right colour and lighting settings for the current environment. The settings of each scene have been set according to a certain style or environment. To change the scene, select Scene modes from the toolbar. To make your own scene, scroll to User defined, and select Options > Change. To copy the settings of another scene, select Based on scene mode and the desired scene. To activate your own scene, select User defined > Select. Capture images in a sequence Select Menu > Media > Camera. To capture several images in a sequence, if enough memory is available, select Sequence mode from the toolbar and press the scroll key. The captured images are shown in a grid on the display. To view an image, scroll to it and press the scroll key. If you used a time interval, only the last image is shown on the display, and the other images are available in Gallery. To send the image, select Options > Send. To send the image to a caller during an active call, select Options > Send to caller. 85 A PI ® a Ea ca O H ß :15 d E rti To deactivate sequence mode, select Sequence mode > p Single shot in the toolbar. d E View captures image Select Menu > Media > Camera. The image you captured is automatically saved in Gallery. If you do not want to keep the image, select Delete from the toolbar. Select from the following toolbar items: Send — Send the image to compatible devices. Send to caller — Send the image to the caller during an active call. Post to — Send the image to your compatible online album (network service). To use the image as the background image, select Options > Set as wallpaper. To add the image to a contact, select Options > Assign to contact. Play a video clip Select Menu > Media > Camera. To play a recorded video clip, select Play from the toolbar. Select from the following toolbar items: Send — Send the video clip to other compatible devices. Send to caller — Send the video clip to the caller during an active call. Post to — Send the video clip to an online album (network service). Delete — Delete the video clip. To enter a new name for the video clip, select Options > Rename video clip. Image settings Select Menu > Media > Camera. To modify still image settings, select Options > Settings and from the following: Image quality — Set the image quality. The better the image quality, the more memory the image consumes. Add to album — Define to which album the captured images are saved. Show captured image — To see the image after the capture, select Yes. To continue capturing images immediately, select Off. Default image name — Define the default name for the captured images. Extended digital zoom — The On (continuous) option allows the zoom increments to be smooth and continuous between the digital and extended digital Record videos Select Menu > Media > Camera. If the camera is in image mode, selectvideo mode from the toolbar. To start recording, press the scroll key. To pause recording, select . Select Continue to resume recording. To stop recording, select . The video clip is 86 automatically saved in Gallery. The maximum length of the video clip depends on the available memory. zoom. The Off option allows a limited amount of zoom while retaining the image resolution. Capture tone — Set the tone that sounds when you capture an image. Memory in use — Select where to store your images. Restore camera settings — Restore the camera settings to the default values. Video settings Select Menu > Media > Camera. Select Options > Settings and from the following: Video quality— Set the quality of the video clip.Select Sharing, if you want to send the video clip using a multimedia message. The clip is recorded with OCIF resolution, in the 3GPP file format, and the size is limited to 300 kB (approximately 20 seconds). You may not be able to send video clips saved in the MPEG-4 file format in a multimedia message. Audio recording — Select Mute if you do not want to record sound. Add to album — Define to which album the recorded videos are saved. Show captured video — View the first frame of the recorded video clip after the recording stops. To view the entire video clip, select Play from the toolbar. Default video name — Define the default name for recorded video clips. Memory in use — Select where to store your video clips. Restore camera settings — Restore the camera settings to the default values. Gallery Ah # ut Gallery iii Select .Menu > Media > Gallery. Galleryis a storage place for your images, video and sound clips, songs, and streaming links. Min view Select tenu > Media > Gallery. Select from the following: Images ri — View images and video clips in Photos. Video clips CJ — View video clips in Video centre. Songs Mr — Open Music player. Sound clip! j , — Listen to sound clips. Streaming nmcsr — View and open streaming links. Presentations ,, J' — View presentations. You can browse and open folders and copy and move items to folders. You can also create albums and copy and add items to albums. Files stored on your compatible memory card (if inserted) are indicated with D. To open a file, select the file from the list. Video clips and streaming links open and play in Video centre, and music and sound clips in Music player. To copy or move files to another memory location, select a file, Options > Move and copy, and the appropriate option. 87 This folder contains all the sound clips you have downloaded from the web. The sound clips created with the Recorder application with MMS optimised or normal quality settings are also saved in this folder, but the sound clips created with high quality settings are stored in the Music player application. To listen to a sound file, select the file from the list. To rewind or fast-forward, scroll left or right. To download sounds, select Downld. sounds. Sound clips W Select Menu > Media > Gallery and Sound clips. Presentations Select Menu > Media > Gallery. With presentations, you can view scalable vector graphics (SVG) and flash files (SWF), such as cartoons and maps. SVG images maintain their appearance when printed or viewed with different screen sizes and resolutions. To view files, select Presentations. Go to an image, and select Options > Play.To pause playing, select Options > 88 Pause. To zoom in, press 5. To zoom out, press O. To rotate the image 90 degrees clockwise or anticlockwise, press 1 or 3, respectively. To rotate the image 45 degrees, press 7 or 9. To switch between full and normal screen mode, press*. Photos About Photos SelectMenu > Media > Gallery > Imagesandfromthe following: Captured —View all the images and videos you have captured. h View images and videos categorised by the month they where captured. a,_ — View the default albums and the ones you have created. Tags — View the tags you have created for each item. Downloads — View items and videos downloaded from the web or received as a multimedia or e-mail message. — View all items. —Postyourimagesorvideostotheweb. Files stored on your compatible memory card (if inserted) are indicated with D. To copy or move files to another memory location, select a file, Options > Move and copy, and from the available options. streaming links Select Menu > Media > Gallery and Streaming links. To open a streaming link, select the link from the list. To add a new streaming link, select Options > New link. View images and videos Select Menu > Media > Gallery > Images and from the following: All — View all images and videos. Captured — View images captured and video clips recorded with the camera of your device. Downloads — View downloaded video clips. Images and video clips can also be sent to you from a compatible device. To be able to view a received image or video clip in Photos, you must first save it. The images and video clip files are in a loop and ordered by date and time. The number of files is displayed. To browse the files one by one, scroll left or right. To browse files in groups, scroll up or down. To open a file, select the file. When an image opens, to zoom in the image, use the zoom keys. The zooming ratio is not stored permanently. To edit an image or a video clip, select To print your images on a compatible printer, select Options > To printer or kiosk. To move images to an album for later printing, select > Ito album > Print later. View and edit file details Select Menu > Media > Gallery > Images. Go to an item. To view and edit image or video properties, select Options > Details > View and edit and from the following: Tags —Viewthe currently used tags. To add more tags to the current file, select Add. Description — View a free-form description of the file. To add a description, select the field. Title — View the thumbnail image of the file and the current file name. To edit the file name, select the file name field. Albums — View in which albums the current file is located. Resolution — View the size of the image in pixels. Duration — View the length of the video. Usage rights — To view the DRM rights of the current file, select View. Organise images 011U V1UCli Select Menu > Media > Gallery > Images. You can organise files as follows: To view items in the Tags view, add tags to the items. To view items by months, select Months. To create an album to store items, select Albums > Options > New album. To add an image or a video clip to an album, select the item and Options > Add to album. All anwr , • `!~ . F -- Lake + '1119.11.2007 10.50 7 kBo 414/17k Back r 89 To delete an image or video clip, select the item and :p Delete from the active toolbar. d E Active toolbar The active toolbar is available onlywhen you have selected an image or a video clip in a view. In the active toolbar, go to different items, and select the desired option. The available options vary depending on the view you are in and whether you have selected an image or a video clip. To hide the toolbar, select Options > Hide toolbar. To activate the active toolbar when it is hidden, press the scroll key. Select an image or a video clip and from the following: U View the image in landscape or portrait mode. al Play the video clip. Send the image or video clip. * Upload the image or video clip to a compatible online album (only available if you have set up an account for a compatible online album). To create a new album, select Options > New album. To add an image or a video clip to an album, select the item and Options > Add to album. A list of albums opens. Select the album to which you want to add the image or video clip. The item you added to the album is still visible in Photos. To remove an image or a video clip from an album, select the album and the item, and Options > Remove from album. Taal Select Menu > Media > Gallery > Images. Use tags to categorise media items in Photos. You can create and delete tags in Tag manager. Tag manager shows the currently used tags and the number of items associated with each tag. To open Tag manager, select an image or video clip and Options > Details > Tag manager. To create a tag, select Options > New tag. To assign a tag to an image, select the image and Options > Add tags. To see the tags you have created, select Tags. The size of the tag name corresponds to the number of items the tag is assigned to. To view all the images associated with a tag, select the tag from the list. To view the list in alphabetical order, select Options > Alphabetical. To view the list in most frequently used order, select Options > Most used. v Add the item to an album. Manage tags and other properties of the item. Albums Select Menu > Media > Gallery > Images and Albums. 90 With albums, you can conveniently manage your images and video clips. To remove an image from a tag, select the tag and the image, and select Options > Remove from tag. Slide show Select Menu > Media > Gallery > Images. To view your images as a slide show, select an image and Options > Slide show > Play forwards or Play backwards. The slide show starts from the selected file. To view only the selected images as a slide show, select Options > Mark/Unmark > Mark to mark images. To start the slide show, select Options > Slide show > Play forwards or Play backwards. To resume a paused slide show, select Continue. To end the slide show, select End. To browse the images, scroll left or right. Before starting the slide show, to adjust the slide show settings, select Options > Slide show > Settings and from the following: Music — Add sound to the slide show. Song — Select a music file from the list. Delay between slides —Adjust the tempo of the slide show. Transition — Make the slide show move smoothly from one slide to another, and zoom in and out in the images randomly. To adjust the volume during the slide show, use the volume key. Edit images Image editor To edit the pictures after taking them or the ones already saved in Photos, select Options > Edit. The image editor opens. To open a grid where you can select different edit options indicated by small icons, select Options > Apply effect . You can crop and rotate the image; adjust the brightness, colour, contrast, and resolution; and add effects, text, clip art, or a frame to the picture. Crop image To crop an image, select Options > Apply effect > Crop, and a predefined aspect ratio from the list. To crop the image size manually, select Manual. If you select Manual, a cross appears in the upper left corner of the image. Use the scroll key to select the area to crop, and select Set. Another cross appears in the lower right corner. Again select the area to be cropped. To adjust the first selected area, select Back. The selected areas form a rectangle that forms the cropped image. If you selecta predefined aspect ratio, selectthe upper left corner of the area to be cropped. To resize the highlighted area, use the scroll key. To freeze the selected area, press the scroll key. To move the area within the picture, use the scroll key. To select the area to be cropped, press the scroll key. Reduce red-eye To reduce red-eye in an image, select Options > Apply effect > Red eye reduction. ß d ~ 91 ea .^ ß w E Move the cross onto the eye, and press the scroll key. A loop appears on the display. To resize the loop to fit the size of the eye, use the scroll key. To reduce the redness, press the scroll key. When you have finished editing the image, press Done. To save the changes and return to the previous view, press Back. Useful cFiirtrlltç You can use the following shortcuts when editing images: To view a full-screen image, press *. To return to the normal view, press * again. To rotate an image clockwise or counterclockwise, press 3 or 1. To zoom in or out, press 5 or O. To move on a zoomed image, scroll up, down, left, or right. —to trim the video and markthe sections you want to keep in the video clip To take a snapshot of a video clip, in the cut video view, select > . In the thumbnail preview view, press the scroll key, and select snapsho . Print images Image print To print images with Image print, select the image you want to print, and the print option in Photos, camera, image editor, or image viewer. Use Image print to print your images using a compatible USB data cable, or Bluetooth connectivity. You can also print images using wireless LAN. If a compatible memory card is inserted, you can store the images to the memory card, and print them using a compatible printer. You can only print images that are in .jpeg format. The pictures taken with the camera are automatically saved in .jpeg format. Printer selection To printimages with Image print, selectthe image and the print option. When you use Image print for the first time, a list of available compatible printers is displayed. Select a printer. The printer is set as the default printer. To use a printer compatible with PictBridge, connect the compatible data cable before you select the print option, and check that the data cable mode is set to Image Edit videos The video editor supports .3gp and .mp4 video file formats, and .aac, .amr, .mp3, and .wav audio file formats. It does not necessarily support all features of a file format or all the variations of file formats. To edit video clips in Photos, scroll to a video clip, select Options > Edit, and from the following: Merge — to add an image or a video clip to the beginning or the end of the selected video clip Change sound — to add a new sound clip, and to 92 • replace the original sound in the video clip. Add text — to add text to the beginning or the end of the video clip print or Ask on connection. The printer is automatically displayed when you select the print option. If the default printer is not available, a list of available printers is displayed. To change the default printer, select Options > Settings > Default printer. Print preview After you select the printer, the selected images are displayed using predefined layouts. To change the layout, scroll left or right to browse through the available layouts for the selected printer. If the images do not fit on a single page, scroll up or down to display the additional pages. Print settings The available options vary depending on the capabilities of the printing device you selected. To set a default printer, select Options > Default printer. To select the paper size, select Paper size, the size of paper from the list, and OK. Select Cancel to return to the previous view. Share online About Share online Select Menu > Media > Share online. With Share online (network service), you can post your images, video clips, and sound clips from your device to compatible online sharing services, such as albums and blogs. You can also view and send comments to the posts in these services, and download content to your compatible Nokia device. The supported content types and the availability of the Share online service may vary. Subscribe to services Select Menu > Media > Share online. To subscribe to an online sharing service, go to the service provider's website, and check that your Nokia device is compatible with the service. Create an account as instructed on the website. You receive a user name and password needed to set up your device with the account. To activate a service, open the Share online application in your device, select a service and Options > Activate. Allow the device to create a network connection. If you are prompted for an internet access point, select one from the list. Sign in to your account as instructed on the service provider's website. For the availability and cost of the third party services and data transfer costs, contact your service provider or the relevant third party. Manage your accounts To view your accounts, select Options > Settings > My accounts. 93 RI To create a new account, select Options > Add new 1p account. • To change your user name or password for an account, select the account and Options > Open. To set the account as the default when sending posts from your device, select Options > Set as default. To remove an account, select the account and Options > Delete. Create a post Select Menu > Media > Share online. To post media files to a service, go to a service, and select Options > New upload. If the online sharing service provides channels for posting files, select the desired channel. To add an image, video clip, or sound clip to the post, select Options > Insert. Enter a title or description for the post, if available. To add tags to the post, select Tags:. To send the post to the service, select Options > Upload. Post files from Photos You can post your files from Photos to an online sharing service. 1. Select Menu > Media > Gallery > Images and the 94 files you want to post. Select Options > Send > Upload and the desired account. Edit your post as required. Select Options > Upload. One-click upload One-click upload lets you postimages to an online sharing service immediately after capturing them. To use one-click upload, capture an image with your device camera, and select the online sharing icon from the toolbar. Tag list Select Menu > Media > Share online. Tags describe the content of the post, and help viewers find content in the online sharing services. To view the list of available tags when creating a post, select Tags:. To add tags to your post, select a tag from the list and Done. To add several tags to the post, select each tag and Options > Mark/Unmark > Mark. To search for tags, enter the search text in the search field. To add a tag to the tag list, select Options > New tag. Manage posts in Outbox Select Menu > Media > Share online. Outbox shows the posts you are currently uploading, posts that have failed to upload, and the posts you have sent. To open Outbox, select Outbox > Options > Open. To start uploading a post, select the post and Options > Upload now. To cancel uploading a post, select the post and Options > Cancel. To delete a post, select the post and Options > Delete. View service content Select Menu > Media > Share online. To view the content of a service, select the service and Options > Open. To open a feed, select the feed. To open the feed in the browser, select the service provider's website. To view comments related to a file, select the file and Options > View comments. To view a file in full screen mode, select the file. To update a feed, select the feed and Options > Update now. If you see an i nte resting file and want to download the entire feed to your device, select the file and Options > Subscribe to contact. Service provider settings Select Menu > Media > Share online. To view the list of service providers, select Options > Settings > Service providers. To check the details of a service, select the service from the list. To delete the selected service, select Options > Delete. Edit account settings Select Menu > Media > Share online. To edit your accounts, select Options > Settings > My and an account. To change the user name for the account, select User To change the password for an account, select To change the account name, select Account name. To determine the size for images that you post, select Upload image size > Original, Medium (1024 x 768 pixels), or Small (640 x 480 pixels). Edit advanced settings Select Menu > Media > Share online. To edit the advanced settings, select Options > Settings > Advanced. To only use a wireless LAN MILAN) connection for sharing, select Use cellular > Disabled. To also allow a packet data connection, select Enabled. 95 ß To allow sharing and downloading items while outside ß your home network, select Allow roaming > Enabled. To download new items from the service automatically, select Download interval and the interval for the downloads. To download items manually, select Manual. Data counters Select Menu > Media > Share online. To check the amount of data you have uploaded and downloaded, select Options > Settings > Data transferred. To reset the counters, select Options > Clear sent, Clear received, or Clear all. Music player T.4 Select Menu > Media > Music player. Music player supports file formats such as MC, AAC+, eAAC +, MP3, and WMA. Music player does not necessarily support all features of a file format or all the variations of file formats. Play a song Select Menu > Media > Music player. To add all available songs to the music library, select Options > Refresh library. 96 To play a song, select the desired category, and the song. To pause playback, press the scroll key; to resume, press the scroll key again. To stop playback, scroll down. To fast-forward or rewind, press and hold the scroll key to the right or left. To skip to the next item, scroll right. To return to the beginning of the item, scroll left. To skip to the previous item, scroll left again within 2 seconds after a song has started. To modify the tone of the music playback, select Options > Equaliser. To modify the balance and stereo image, or to enhance the bass, select Options > Settings. To return to the home screen and leave the player playing in the background, press the end key briefly. Ouvarning: Continuous exposure to high volume may damage your hearing. Listen to music at a moderate level, and do not hold the device near your ear when the loudspeaker is in use. Playlists To view and manage playlists, select Music library > Playlists. To create a new playlist, select Options > New playlist. To add songs to the playlist, select the song and Options > Add to playlist > Saved playlist or New playlist. To reorder songs in a playlist, scroll to the song you want to move, and select Options > Reorder playlist. Ovi Music With Ovi Music (network service), you can search, browse, purchase, and download music to your device. The Ovi Music service will eventually replace the Music store. Select Menu > Media > Ovi Music. To download music, you first need to register for the service. Downloading music may involve additional costs and the transmission of large amounts of data (network service). For information about data transmission charges, contact your network service provider. To access Ovi Music, you must have a valid internet access point in the device. You may be asked to select the access point to use when connecting to Ovi Music. Select the access point — Select Default access point. The availability and appearance of Ovi Music settings may vary. The settings may also be predefined and you may not be able to modify them. When browsing Ovi Music, you may be able to modify the settings. Modify Ovi Music settings — Select Options > Setting.. Ovi Music is not available for all countries or regions. Transfer music from a computer You can use the following methods to transfer music: To install Nokia Ovi Player to manage and organise your music files, download the PC software from www.ovi.com, and follow the instructions. To view your device on a computer as a mass memory device where you can transfer any data files, make the connection with a compatible USB data cable or Bluetooth connectivity. If you are using a USB data cable, select Mass storage as the connection mode. A compatible memory card must be inserted in the device. To synchronise music with Windows Media Player, connect a compatible USB data cable, and select Media as the connection mode. A compatible memory card must be inserted in the device. To change the default USB connection mode, select Menu > Ctrl. panel > Connectivity > USB and USB connection mode. Preset frequency settings Select Menu > Media > Music player and Options > Go to Now playing > Options > Equaliser. To use a preset frequency setting when playing music, select the frequency setting you want to use and Options > Activate. To modify the frequency of a preset setting, select Options > Edit and a frequency band, and scroll up or down to adjust its value. You hear your frequency adjustment immediately in the playback. To reset the frequency bands to their original values, select Options > Reset to defaults. 97 ro :1::: ai E To create your own frequency setting, select Options > New preset. Enter a name for the frequency setting. Scroll up or down to move between the frequency bands, and set the frequency for each band. RealPlayei q Select Menu > Media > RealPlayer. RealPlayer plays video and sound clips that are stored on your device, transferred from an e-mail message, or a compatible computer, or streamed to your device over the web. Supported file formats include MPEG-4, MP4 (not streaming), 3GP, RV, RA, AMR, and Midi. RealPlayer does not necessarily support all variations of a media file format. Play video clips and stream links To play a video clip, select Video clips and a clip. To list recently played files, in the application main view, select Recently played. To stream content over the air (network service), select Streaming links and a link. RealPlayer recognises two kinds of links: an rtsp:// URL and an http:// URL that points to a RAM file. Before the content begins streaming, your device must connect to a website and buffer the content. If a network connection problem causes a playback error, RealPlayer attempts automatically to reconnect to the internet access point. gg To download video clips from the web, select Downld. videos. To adjust the volume during playback, use the volume keys. To fast-forward during playback, scroll right and hold. To rewind during play, scroll left and hold. To stop the playback or streaming, select Stop. Buffering or the connection to the streaming site stops, the playback of the clip stops, and the clip rewinds to the beginning. To view the video clip in normal screen mode, select Options > Continue in normal scr.. View information abuuL a media clip To viewthe properties of a video or sound clip, or web link, select Options > Clip details. Information may include for example the bit rate or the internet link of a streaming file. RealPlayer settings Select Menu > Media > RealPlayer. You may receive RealPlayer settings in a message from your service provider. To define the settings manually, select Options > Settings > Video or Streaming. Recorder Select Menu > Media > Recorder. With the Recorder application, you can record voice memos and telephone conversations. The recorder cannot be used when a data call or GPRS connection is active. To record a sound clip, select To stop recording a sound clip, select 0. To listen to the sound clip, select D To select the recording quality or where you want to save your sound clips, select Options > Settings. Recorded sound clips are saved in the Sound clips folder in Gallery. To record a telephone conversation, open recorder during a voice call, and select 0. Both parties hear a tone at regular intervals during recording. Flash player With Flash player, you can view, play, and interact with flash files made for mobile devices. To open Flash player and play a flash file, select the file. To send a flash file to compatible devices, select Options > Send. Copyright protection may prevent the sending of some flash files. To switch between flash files saved in the device memory or on the memory card, scroll to the corresponding tabs. To change the flash file quality, select Options > Quality when you are playing the flash file. If you select High, the playback of some flash files may appear uneven and slow due to their original settings. Change the quality setting of such files to Normal or Low for improved playback. To organise your flash files, select Options > Organise. FM radio The FM radio depends on an antenna other than the wireless device antenna. A compatible headset or accessory needs to be attached to the device for the FM radio to function properly. Select Menu > Media > Radio > FM radio. The quality of the radio broadcast depends on the coverage of the radio station in that particular area. Listen to the radio Select Menu > Media > Radio > FM radio. The quality of the radio broadcast depends on the coverage of the radio station in that particular area. You can make a call or answer an incoming call while listening to the radio. The radio is muted when there is an active call. To start a station search, select /\ or 0. If you have saved radio stations in your device, to go to the next or previous saved station, select N] or []~. Select Options and from the following: Activate loudspeaker — Listen to the radio using the loudspeaker. Manual tuning — Change the frequency manually. 99 D ru :15 d E Station directory — View available stations based on location (network service). Save station — Save the station to which you are currently tuned to your station list. Stations — Open the list of your saved stations. Play in background — Return to the home screen while listening to the FM radio in the background. °Warning: Continuous exposure to high volume may damage your hearing. Listen to music at a moderate level, and do not hold the device near your ear when the loudspeaker is in use. Saved stations Select Menu > Media > Radio > FM radio. To open the list of your saved stations, select Options > Stations. To listen to a saved station, select Options > Station > Listen. To change station details, select Options > Station > Edit. To select the region where you currently are, select Options > Settings > Current region. This setting is displayed only if there is no network coverage when you start the application. Nokia Internet Radio is Select Menu > Media > Radio > Internet radio. With the Nokia Internet Radio application (network service), you can listen to available radio stations on the internet. To listen to radio stations, you must have a wireless LAN (WLAN) or packet data access point defined in your device. Listening to the stations may involve the transmission of large amounts of data through your service provider's network. The recommended connection method is WLAN. Check with your service provider for terms and data service fees before using other connections. For example, a flat rate data plan can allow large data transfers for a set monthly fee. Listen to Internet radio stations Select Menu > Media > Radio > Internet radio. To listen to a radio station on the internet, do the following: 1. Select a station from your favourites or the station directory, or search for stations by name from the Nokia Internet Radio service. To add a station manually, select Options > Add station manually. You can also browse for station FM radio settings Select Menu > Media > Radio > FM radio. To automatically search for alternative frequencies if the reception is weak, select Options > Settings > Alternative frequencies > Auto scan on. 100 To set the default access point for the radio, select Options > Settings > Access point. links with the Web browser application. Compatible links are automatically opened in the Internet Radio application. 2. Select Options > Listen. The Now playing view opens, displaying information about the currently playing station and song. To pause the playback, press the scroll key; to resume, press the scroll key again. To view station information, select Options > Station information (not available if you have saved the station manually). If you are listening to a station saved in your favourites, scroll left or right to listen to the previous or next saved station. Favourite stations Select Menu > Media > Radio > Internet radio. To view and listen to your favourite stations, select Favour . To add a station manually to favourites, select Options > Add station manually. Enter the web address of the station and a name that you want to appear in the favourites list. To add the currently playing station to favourites, select Options > Add to Favourites. To view station information, to move a station up or down in the list, or to delete a station from favourites, select Options > 'ration and the desired option. To view only stations beginning with particular letters or numbers, start entering the characters. Matching stations are displayed. Search for stations Select Menu > Media > Radio > Intc To search for radio stations in the Nokia Internet Radio service by name, do the following: Select Search. Enter a station name or the first letters of the name in the search field, and select iearch. Matching stations are displayed. To listen to a station, select the station and To save a station to your favourites, select the station and > To make another search, select Options > Search again. Station directory Select Menu > Media > Radio > Internet radio and Station directory. The station directory is maintained by Nokia. If you want to listen to internet radio stations outside the directory, add station information manually or browse for station links on the internet with the Web browser application. Select from the following: • Browse by _ — View the available radio station genres. 101 Security and data management Browse by language — View the languages in which there are stations broadcasting. Browse by country/region — View the countries in which there are stations broadcasting. Top stations — View the most popular stations in the directory. Internet radio settings Select Menu > Media > Radio > Internet radio and Options > Settings. To select the default access point to connect to the network, select Default access point and from the available options. If you want the device to ask you to select the access point every time you open the application, select To change the connection speeds for different connection types, select from the following: GPRS connection bitrate — GPRS packet data connections 3G connection bitrate — 3G packet data connections Wi-Fi connection bitrate — MAN connections The quality of the radio broadcast depends on the selected connection speed. The higher the speed, the better the quality. To avoid buffering, use the highest quality only with high speed connections. Security and data management Manage the data and software on your device, and take care of the security of the device and its contents. Important: Your device can only support one antivirus application. Having more than one application with antivirus functionality could affect performance and operation or cause the device to stop functioning. Lock thp devicF To lock the device, in the home screen, press the power key, and select Lock phone. To unlock your device, select Unlock > OK, enter the lock code, and select OK. To change the lock code, select Menu > Ctrl. panel > Settings and General > Security > Phone and SIM card. Enter the old code and then the new code twice. A minimum of 6 characters is required, and numbers, symbols, and upper and lower case letters can be used. Keep the lock code secret and in a safe place separate from your device. If you forget the lock code and your device is locked, your device will require service. Additional charges may apply, and all the personal data in your device may 102 The lock code protects your device against unauthorised use. The preset code is 12345. Security and data management be deleted. For more information, contact a Nokia Care point or your device dealer. You can also lock the device remotely by sending a text message to the device. Lock your device remotely To enable remote locking, select Menu > Ctrl. panel > Settings and General > Security > Phone and SIM card > Remote phone locking > Enabled. Enter the text message content. It can be 5-20 characters, and both upper and lower case letters can be used. Enter the same text again to verify it. Enter the lock code. To lock the device remotely, write the predefined text, and send it to your device as a text message. To unlock your device, you need the lock code. Memory card security Select Menu > Office > File mgr.. You can protect a memory card with a password to prevent unauthorised access. To seta password, select Options > Memory card password > Set. The password can be up to 8 characters long and is case-sensitive. The password is stored in your device. You do not need to enter it again while you use the memory card on the same device. If you use the memory card on another device, you are asked for the password. Not all memory cards support password protection. To remove the memory card password, select Options > Memory card password > Remove. When you remove the password, the data on the memory card is not protected against unauthorised use. To open a locked memory card, select Options > Unlock memory card. Enter the password. If you cannot recall the password to unlock a locked memory card, you may reformat the card, in which case the card is unlocked and password removed. Formatting a memory card deletes all data stored on the card. Encryption Select Menu > Ctrl. panel > Phone > Encryption. Encrypt your device or memory card to prevent outsiders from accessing your important information. Encrypt device memory or memory card To encrypt the device memory, select Phone memory. To encrypt the memory card, select Memory card and from the following: Encrypt without saving key — Encrypt the memory card without saving the encryption key. If you select this option, you cannot use the memory card in other devices, and if you restore factory settings, you cannot decrypt the memory card. Encrypt and save key — Encrypt the memory card and save the key manually in the defaultfolder. For security, 103 store the key to a safe place outside the device. For Security and data management example, you can send the key to your computer. Enter a pass phrase for the key and a name for the key file. The pass phrase should be long and complex. Encrypt with restored key — Encrypt the memory card with a key you have received. Select the key file, and enter the pass phrase. Decrypt device memory or memory card Always remember to decrypt the device memory and/or the memory card before updating the device software. To decrypt the device memory, select Phone memory. To decrypt the memory card without destroying the encryption key, select Memory card > Decrypt. To decrypt the memory card and destroy the encryption key, select Memory card > Decrypt and turn off encryption. programmed into your device. Call barring and call diverting cannot be active at the same time. You need your PIN2 code to activate and deactivate fixed dialling or edit your fixed dialling contacts. Contact your service provider for your PIN2 code. Select Options and from the following: Activate fixed dialling — Activate the fixed dialing. Deactivate fixed dialling — Deactivate the fixed dialing. NewSIM contact — Enterthe contact name and phone number to which calls are allowed. Add from Contacts — Copy a contact from the list of contacts to the fixed dialling list. To send text messages to the SIM contacts while the fixed dialling service is active, you need to add the text message centre number to the fixed dialling list. Certificate manager Fixed dialling Select Menu > Contacts and Options > SIM numbers > Fixed dial contacts. With the fixed dialling service, you can restrict calls from your device to certain phone numbers. Not all SIM cards support the fixed dialling service. For more information, contact your service provider. When security features that restrict calls are in use (such as call barring, closed user group, and fixed dialling), calls 104 may be possible to the official emergency number Select Menu > Ctrl. panel > Settings and General > Security > Certificate management. Digital certificates are used to verify the origins of software but do not guarantee safety. There are four different types of certificates: authority certificates, personal certificates, trusted site certificates, and device certificates. During a secure connection, a server may send a server certificate to your device. Upon receipt, it is checked through an authority certificate stored in your device. You receive notification if the identity of the server is not authentic or if you do not have the correct certificate in your device. Security and data management You can download a certificate from a web site, or receive a certificate as a message. Certificates should be used when you connect to an online bank or a remote server to transfer confidential information. They should also be used if you want to reduce the risk of viruses or other malicious software, and to check the authenticity of software when you download and install software to your device. Tip: When you add a new certificate, check its authenticity. View certificate details You can only be sure of the correct identity of a server when the signature and the validity period of a server certificate have been checked. To view certificate details, open a certificate folder, and select a certificate and Options > Certificate details. One of the following notes may appear: Certificate not trusted — You have not set any application to use the certificate. You may want to change the trust settings. Expired certificate — The period of validity has ended for the selected certificate. Certificate not valid yet — The period of validity has not yet begun for the selected certificate. Certificate corrupted — The certificate cannot be used. Contact the certificate issuer. Certificate trust settings Select Menu > Ctrl. panel > Settings and General > Security > Certificate management. Trusting a certificate means that you authorise it to verify web pages, e-mail servers, software packages, and other data. Only trusted certificates can be used to verify services and software. nd °Important: Even if the use of certificates makes the risks involved in remote connections and software installation considerably smaller, they must be used correctly in order to benefit from increased security. The existence of a certificate does not offer any protection by itself; the certificate manager must contain correct, authentic, or trusted certificates for increased security to be available. Certificates have a restricted lifetime. If "Expired certificate" or "Certificate not valid yet" is shown, even if the certificate should be valid, check that the current date and time in your device are correct. Before changing any certificate settings, you must make sure that you really trust the owner of the certificate and that the certificate really belongs to the listed owner. To change the trust settings, select a certificate and Options > Trust settings. Scroll to an application field, and press the scroll key to select Yes or No. You cannot change the trust settings of a personal certificate. Depending on the certificate, a list of applications that can use the certificate is displayed: Symbian installation — New Symbian operating system application. Internet — E-mail and graphics. 105 Security and data management App. installation — New Java application. Online certif. check — Online certificate status protocol. View and edit security modules Select Menu > ctrl. panel > Settings and General > Security > Security module. To view or edit a security module, select the module from the list. To view detailed information about a security module, select Options > Security details. To edit the PIN codes for the security module, open the module, and select Module PIN to edit the PIN code for the security module or Signing PIN to edit the PIN code for digital signatures. You may not be able to change these codes for all security modules. The key store contains the contents of the security module. To delete the key store, select Options > . You may not be able to delete the key store of all security modules. and different configuration settings from your service providers or company information management department. Configuration settings may include connection and other settings used by different applications in your device. The available options may vary. The remote configuration connection is usually started by the server when the device settings need to be updated. To create a new server profile, select Options > Server profiles > Options > New server profile. You may receive these settings from your service provider in a configuration message. If not, define the following: Server name — Enter a name for the configuration server. Server ID — Enter the unique ID to identify the configuration server. Server password — Enter a password to identify your device to the server. Access point — Select the access point to use for the connection, or create a new access point. You can also choose to be asked for the access point every time you start a connection. This setting is available only if you have selected Internet as the bearer type. Host address — Enter the web address of the configuration server. Port — Enter the port number of the server. User name and Passwora — Enter your user ID and password for the configuration server. Allow configuration — Select to allow the server to initiate a configuration session. Auto-accept all requests — Select if you do not want the server to ask for your confirmation when it initiates a configuration session. Remote configuration Select Menu > ctrl, panel > Phone > Device mgr.. With Device manager, you can manage settings, data, and software on your device remotely. 106 You can connect to a server, and receive configuration settings for your device. You may receive server profiles Security and data management Network authentication — Select whether to use http authentication. Network user name and Network password — Enter your user ID and password for the http authentication. This setting is available only if you have selected Network authentication to be used. To connectto the server and receive configuration settings for your device, select Options > Start configuration. To viewthe configuration log of the selected profile, select Options > View log. To update the device software over the air, select Options > Checkfor updates. The update does noterase your settings. When you receive the update package on your device, follow the instructions on the display. Your device is restarted once the installation is complete. Downloading software updates may involve the transmission of large amounts of data (network service). Make sure that the device battery has enough power, or connect the charger before starting the update. °Warning: If you install a software update, you cannot use the device, even to make emergency calls, until the installation is completed and the device is restarted. Be sure to back up data before accepting installation of an update. Application manager With Application manager, you can see the software packages installed in your device. You can view details of installed applications, remove applications, and define installation settings. You can install two types of applications and software to your device: JME applications based on Java technology with the .jad or .jar file extensions Other applications and software suitable for the Symbian operating system with the .sis or .sisx file extensions Only install software that is compatible with your device. Install applications and software You can transfer installation files to your device from a compatible computer, download them during browsing, or receive them in a multimedia message, as an e-mail attachment, or using other connectivity methods, such as Bluetooth connectivity. You can use Nokia Application Installer in Nokia Ovi Suite to install an application to your device. Select Menu > Ctrl. panel > App. mgr.. The installation files are in the Installation files folder, and installed applications in the Installed apps. folder. Icons indicate the following: .sis or .sisx application Java application ® Application not fully installed Ei Application installed on the memory card 107 Security and data management 108 °Important: Only install and use applications and other software from trusted sources, such as applications that are Symbian Signed or have passed the Java VerifiedTM testing. Before installation, note the following: To view the application type, version number, and the supplier or manufacturer of the application, select Options > View details. To display the security certificate details of the application, select Details: > Certificates: > View details. If you install a file that contains an update or repair to an existing application, you can only restore the original application if you have the original installation file or a full backup copy of the removed software package. To restore the original application, remove the application, and install the application again from the original installation file or the backup copy. The JAR file is required for installing Java applications. If it is missing, the device may ask you to download it. If there is no access point defined for the application, you are asked to select one. When you are downloading the JAR file, you may need to enter a user name and password to access the server. You obtain these from the supplier or manufacturer of the application. To install an application or software, do the following: 1. To locate an installation file, select Menu > Ctrl. panel > App. mgr. and Installation files. Alternatively, search installation files using File manager, or select Messaging > Inbox, and open a message that contains an installation file. 2. In Application manager, select the application you want to install. During installation, the device shows information about the progress of the installation. If you install an application without a digital signature or certification, the device displays a warning. Continue installation only if you are sure of the origin and contents of the application. To start an installed application, select the application. If the application does not have a default folder defined, it is installed in the Installations folder in the main menu. To see which software packages are installed or removed and when, select Options > View log. Important: Your device can only support one antivirus application. Having more than one application with antivirus functionality could affect performance and operation or cause the device to stop functioning. After you install applications to a compatible memory card, installation files (.sis, .sisx) remain in the device memory. The files may use large amounts of memory and preventyou from storing other files. To maintain sufficient memory, use Nokia Ovi Suite to back up installation files to a compatible PC, then use the file manager to remove the installation files from the device memory. If the .sis file is a message attachment, delete the message from the Messaging inbox. Remove applications and software Select Menu > Ctrl. panel > App. mgr.. Security and data management Scroll to a software package, and select Options > Uninstall. Select Yes to confirm. If you remove software, you can only reinstall it if you have the original software package or a full backup of the removed software package. If you remove a software package, you may no longer be able to open documents created with that software. If another software package depends on the software package that you removed, the other software package may stop working. For more information, see the documentation of the installed software package. Application manager settings Select Menu > Ctrl. panel > App. mgr.. Select Options > Settings and from the following: Software installation — Select whether Symbian software that has no verified digital signature can be installed. Online certificate check — Check the online certificates before installing an application. Default web address — Set the default address used when checking online certificates. Some Java applications may require that a message be sent or a network connection be made to a specific access point to download extra data or components. Licenses About Licenses Select Menu > Ctrl. panel > Phone > licences. Some media files, such as images, music, orvideo clips, are protected by digital usage rights. The licenses for such files may allow or restrict their usage. For example, with some licenses you may listen to a song only a limited number of times. During one playback session you may rewind, fast-forward, or pause the song, but once you stop it, you have used one of the instances allowed. Use licences Digital rights management (DRM) protected content comes with an associated licence that defines your rights to use the content. If your device has OMA DRM-protected content, to back up both the licence and the content, use the backup feature of Nokia Ovi Suite. Other transfer methods may not transfer the licence which need to be restored with the content for you to be able to continue the use of OMA DRM-protected content after the device memory is formatted. You may also need to restore the licence in case the files on your device get corrupted. If your device has WMDRM-protected content, both the licence and the content will be lost if the device memory is formatted. You may also lose the licence and the content if the files on your device get corrupted. Losing the licence or the content may limit your ability to use the same content on your device again. For more information, contact your service provider. Some licence may be connected to a specific SIM card, and the protected content can be accessed only if the SIM card is inserted in the device. To view your licences by type, select Valid licences, 109 Invalid licences, or Not in use. Security and data management To view the licence details, select Options > Licence details. The following details are displayed for each media file: Status — The status is Licence is valid, Licence expired, or Licence not yet valid. Content sending — Allowed indicates that you can send the file to another device. Content in phone — Yes indicates that the file is in the device and the path of the file is displayed. No indicates that the related file is not currently in the device. To activate a licence, in the licences main view, select Invalid licences > Options > Get new licence. Establish a network connection atthe prompt, and you are directed to a website where you can purchase rights to the media. To remove file rights, go to the desired file, and select Options > Delete. If there are several rights related to the same media file, all the rights are deleted. The group licence view displays all of the files related to a group right. If you have downloaded multiple media files with the same rights, they are all displayed in this view. You can open the group view from either the valid licences or invalid licences tabs. To access these files, open the group rights folder. bookmarks, or contacts with various compatible applications on a compatible computer or on the internet. You may receive synchronisation settings in a special message from your service provider. A synchronisation profile contains the necessary settings for synchronisation. When you open the Sync application, the default or previously used sync profile is displayed. To modify the profile, scroll to a sync item, and select Mark to include it in the profile or Unmark to leave it out. To manage sync profiles, select Options and the desired option. To synchronise data, select Options > Synchronise. To cancel synchronisation before it finishes, select Cancel. Mobile VPN Select Menu > Ctrl. panel > Settings and Connection > VPN. The Nokia mobile virtual private network (VPN) client creates a secure connection to compatible corporate intranet and services, such as e-mail. Your device connects from a mobile network, through the internet to a corporate VPN gateway that acts as a front door to the compatible corporate network. The VPN client uses IP Security (IPSec) technology. IPSec is a framework of open standards for supporting the secure exchange of data over IP networks. VPN policies define the method used by the VPN client and a VPN gateway to authenticate each other, and the encryption algorithms that they use to help protect the Sync hv Select Menu > Ctrl. panel > Phone > Sync. Sync enables you to synchronise your notes, calendar 110 entries, text and multimedia messages, browser Security and data management confidentiality of data. For a VPN policy, contact your company's IT department. To install and configure the VPN client, certificates, and policies, contact the IT administrator of your organisation. Manage VPN Select from the following: VPN policies — Install, view, and update VPN policies. VPN policy servers — Edit the connection settings of VPN policy servers from which you can install and update VPN policies. A policy server refers to a Nokia Security Service Manager (NSSM), which is not necessarily required. VPN len — View the log for your VPN policy installations, updates and synchronisations, and other VPN connections. Edit VPN access points Select Menu > Ctrl. panel > Settings and Connection > Destinations. An access point is where your phone connects to the network. To use e-mail and multimedia services, or to browse web pages, you must first define internet access points for these services. Virtual private network (VPN) access points pair VPN policies with regularinternet access points to create secure connections. Your service provider may preset some or all access points for your device, and you may not be able to create, edit, or remove them. Select a destination and Options > Edit, and define the following: Connection name — Enter a name for the VPN access point. VPN policy — Select the VPN policy to combine with the Internet access point. Internet access point — Select the internet access point with which to combine the VPN policy to create secure connections for data transfer. Proxy server address — Enter the proxy server address of the private network. Proxy port number — Enter the proxy port number. Use access point — Select whether connections using this access point are established automatically. The settings available for editing may vary. For the correct settings, contact your company's IT department. Use a VPN connection in an application You may have to prove your identity when you log on to the enterprise network. Contact your company's IT department for the credentials. To use a VPN connection in an application, the application must be associated with a VPN access point. Tip: You can configure the application's connection setting to Always ask, in which case you select the VPN access point from a list of connections when a connection is established. 111 H at C E d N In the application in which you want to create a VPN connection, select a VPN access point as the access point. If you are using legacy authentication, enter your VPN user name and passcode or password. If the SecurlD Settings Select Menu > Ctrl. panel > Settings. You can define and modify various settings of your device. Modifying these settings affects the operation of your device across several applications. Some settings may be preset for the device or sent to you in a special message by your service provider. You may not be able to change such settings. Select the setting you want to edit to do the following: Switch between two values, such as on or off. Select a value from a list. Open a text editor to enter a value. Open a slider, and scroll left or right to adjust a value. General settings Select Menu > Ctrl. panel > Settings and Ge Select from the following: 112 • Personalisation — Modify the display settings, and personalise the device. token has become out of synchronisation with the clock of the ACE/Server, enter the next passcode. If you are using certificate-based authentication, you may have to enter the key store password. date ana th. — Change the date and time. Enhancemer — Modify the settings for your accessories. — Modify the sensor settings. — Modify the security settings. — Restore the original settings of the device. — Define the positioning method and server for GPS-based applications. The available options may vary. rersonah)ation settings Select Menu > Ctrl. panel > Settings and General > Personalisation. Display settings To define the level of light that the device needs before switching on the backlight, select Display > Light sensor. To change the text size, select Display > Font size. vi cn _~ ~ ar tel To adjust the length of time the display can be left idle before the screen saver is activated, select Display > Power saver time-out. To select a welcome note or logo for the display, select Display > Welcome note / logo. You can either choose the default welcome note, enter your own text, or select an image. To set how quickly the display dims after the last keypress, select Display > Light time-out. Tone settings Select Menu > Ctrl. panel > Settings. Select General > Personalisation > Tones and from the following:. Ringing tone — Select a ringing tone from the list, or select Downy to open a bookmark folder containing a list of bookmarks for downloading tones using the browser. If you have two alternate phone lines in use, you can specify a ringing tone for each line. Video call tone — Select a ringing tone for video calls. Say caller's name — If you select this setting, and someone from your contacts list calls you, the device sounds a ringing tone that is a combination of the spoken name of the contact and the selected ringing tone. Ringing type — Select how you want the ringing tone to alert you. Ringing volume — Set the volume level of the ringing tone. Message alert tone — Select a tone for received text messages. E-mail alert tone — Select a tone for received e-mail messages. Calendar alarm tone — Select a tone for calendar alerts. Clock alarm tone — Select a tone for clock alarms. Vibrating alert — Set the device to vibrate when you receive a call or message. Keypad tones — Set the volume level of the keypad tones. Warning tones — Turn the warning tones on or off. Language settings Select Menu > Ctrl. panel > Settings and General > Personalisation > Language. Phone language — Set the device language. Writing language — Select the language used for writing notes and messages. Predictive text — Activate predictive text input. Input options — Define the settings for predictive text input. Scroll key lights Select Menu > Ctrl. panel > Settings and General > Personalisation > Notification lights. To set the scroll key to blink slowly when you do not use the device, select Standby br. light. To setthe scroll key to blink rapidly when you have missed calls or received messages, select Notification light, set the blinking time, and select the events you want to be notified of. Settings for One-touch keys Select Menu > Ctrl. panel > Settings and General > Personalisation > One-touch keys. 113 114 To select which application and task is opened when you Ch press a One-touch key, select the key and Options > C Open. E To restore the preset applications and tasks, select tel Restore defaults. Date and time settings Select Menu > Ctrl. panel > Settings and General > Date and time. Select from the following: Date and Time — Set the current date and time. Time zone — Define your time zone. Date format and Date separator — Define the date format and separator. Time format and Time separate — Select whether to use the 12-hour or 24-hour clock system and with which symbol to separate hours and minutes. Clock type — Define the clock type. Clock alarm tone —Selectthe tone for the alarm clock. Alarm snooze time — Define the snooze time for the alarm clock. Workdays — Define the days of the weekthat are work days for you. Automatictime update — Update the time, date, and time zone information automatically (network service). Accessory settings Select Menu > Ctrl. panel > Settings and General > Enhancement. To define which profile is activated when you attach an accessory to your device, select the accessory and Default profile. To set the device to answer phone calls automatically after 5 seconds when an accessory is attached, select the accessory and Automatic answer > On. If the ringing type is set to Beep once or Silent in the selected profile, automatic answering is disabled. To illuminate the device while it is attached to an accessory, select Lights > On. This option is only available for certain accessories. Sensor settings Select Menu > Ctrl. panel > Settings and General > Sensors. To set the device to silence an incoming call or snooze an alarm when you turn the device face down, select Turning control. Security settings Security settings Select Menu > Ctrl. panel > Settings and General > Security. Select from the following: Phone and SIM card — Modify the security settings for your device and SIM card. Certificate management — Manage your security certificates. H 01 C E w N Protected content — Modify your settings for DRM­protected content. Security module — Manage your security module. Avoid using codes that are similar to emergency numbers to prevent accidental dialling of the emergency number. Codes are shown as asterisks. When you change a code, enter the current code, then the new code twice. Device and SIM card security To change the PIN code, select Phone and SIM card > PIN code. The new code must be 4 to 8 digits long. The PIN code protects your SIM card against unauthorised use and is provided with the SIM card. After three consecutive incorrect PIN code entries, the code is blocked, and you need to use the PUK code to unblock it before you can use the SIM card again. To set the keypad to lock automatically after a defined period, select Phone and SIM card > Keypad autolock period. To set a time-out after which the device is automatically locked and can be used only if the correct lock code is entered, select Phone and SIM card > Phone autolock period. Enter a number for the time-out in minutes, or select None to set off the autolock period. When the device is locked, you can still answer incoming calls, and calls may still be possible to the official emergency number programmed into your device. To set a new lock code, select Phone and SIM card > Lock code. The preset lock code is 12345. Enter the currentcode and then the new code twice. The new code can be 4-255 characters long. Both alphabets and digits can be used, and both uppercase and lowercase alphabets are possible. The device notifies you if the lock code is not properly formatted. Restore original settings To restore the original device settings, select Menu > Ctrl. panel > Settings and General > Factory settings. To do this, you need your device lock code. After resetting, the device may take a longer time to switch on. Documents, contact information, calendar entries, and files are unaffected. Positioning settings Select Menu > Ctrl. panel > Settings and General > Positioning. To use a specific positioning method to detectthe location of your device, select Positioning methods. To select a positioning server, select Positioning server. To select which measurement system you want to use for speeds and distances, select Notation preferences > Measurement system. To define in which format the coordinate information is displayed in your device, select Notation preferences > Coordinate format. E-mail key settings Select Menu > Ctrl. panel > Settings and General. 115 H cr1 _C ~ w in To select which mailbox to open with the e-mail key, select E-mail key settings > E-mail key, and press the scroll key. Telephone settings Select Menu > Ctrl. panel > Settings and Phon . Select from the following: Call — Define general call settings. Call divert — Define your call divert settings. See "Call divert', o. 31. Call barring — Define your call barring settings. See "Call barring", o. 32. Network — Adjust the network settings. Internet call alert — Select On to set your device to alert for incoming internet calls. If you select Off, you receive only a notification if you missed a call. This setting is only available if you have defined internet call service settings. Reject call with message — Reject a call, and send a text message to the caller. Message text — Write the standard text message that is sent when you reject a call. Own video in recvd. call — Allow or deny video sending during a video call from your device. Image in video call — Display a still image if video is not sent during a video call. Automatic redial — Set your device to make a maximum of 10 attempts to connect the call after an unsuccessful call attempt. To stop automatic redialling, press the end key. Show call duration — Display the length of a call during the call. Summary after call — Display the length of a call after the call. Speed dialling —Activate speed dialling. Anykey answer — Activate anykey answer. Line in use — This setting (network service) is shown only if the SIM card supports two subscriber numbers, that is, two phone lines. Select which phone line you want to use for making calls and sending text messages. Calls on both lines can be answered irrespective of the selected line. If you select Line 2 and have not subscribed to this network service, you are not able to make calls. When line 2 is selected, 2 is displayed in the home screen. Call settings Select Menu > Ctrl. panel > Settings and Phone > Call. Select from the following: Send my caller ID — Display your phone number to the person you are calling. Send my Internet call ID — Display your internet call address to the person you are calling using an internet call. This setting is only available if you have defined internet call service settings. Call waiting — Set the device to notify you ofincoming calls while you are in a call (network service). Internet call waiting — Set the device to notify you of a new incoming internet call while you are in a call. 116 This setting is only available if you have defined internet call service settings. H lT C E CL) N Line change — Prevent line selection (network service), if supported by your SIM card. To change this setting, you need the PIN2 code. Noise cancellation — Activate earpiece active noise cancellation. Contact search —Activate contact search in the home screen. Network settings Select Menu > Ctrl. panel > Settings and Phone > Network. To select the network mode, select Network mode and Dual mode, UMTS, or GSM. In dual mode, the device switches automatically between networks. Tip: Selecting UMTS enables faster data transfer, but may increase the demand on battery power and reduce the battery life. In regions close to both GSM and UMTS networks, selecting Dual mode may cause constantjumping between the two networks, which also increases the demand on battery power. To select the operator, select Operator selection and Manual to select from available networks, or Automatic to set the device to select the network automatically. To set the device to indicate when it is used in a microcellular network (MCN), select Cell info display > On. Connection settings Select Menu > Ctrl. panel > Settings and Connection. Select from the following: Bluetooth — Edit the Bluetooth settings. USB — Edit the data cable settings. Destinations — Set up new or edit existing access points. Some or all access points may be preset for your device by your service provider, and you may not be able to create, edit, or remove them. VPN — Manage the settings for virtual private networking. Packet data — Define when packet data network is attached, and enter the default packet switched access point name if you use your device as a modem for a computer. Wireless LAN — Set the device to display an indicator when a wireless LAN (WIAN) is available, and define how often the device searches for networks. Video sharing — Enable video sharing, select the SIP profile for video sharing, and define the video saving settings. SIP settings — View or create session initiation protocol (SIP) profiles. XDM profile — Create an XDM profile. The XDM profile is required for many communications applications, for example, presence. Presence — Edit the settings for presence (network service). To register for the service, contact your service provider. Remote drives — Connect the device to a remote drive. Configurations — View and delete trusted servers from which your device may receive configuration settings. APN control — Restrict packet data connections. 117 Access points Create a new access point Select Menu > Ctrl. panel > Settings and Connection > Destinations. You may receive access point settings in a message from a service provider. Some or all access points may be preset for your device by your service provider, and you may not be able to change, create, edit, or remove them. When you select one of the access point groups (4), Or, ? r, a), you can see the access point types: indicates a protected access point indicates a packet data access point cgs indicates a wireless LAN (WLAN) access point Tip: You can create internet access points in a WLAN with the WLAN wizard. To create a new access point, select -j Access point. The device asks to check for available connections. After the search, connections that are already available are displayed and can be shared by a new access point. If you skip this step, you are asked to select a connection method and to define the settings needed. To edit the settings of an access point, select one of the access point groups, scroll to an access point, and select Options > Edit. Use the instructions provided by your service provider to edit the following: Connection name — Enter a name for the connection. Data bearer — Select the data connection type. 118 Depending on the data connection you select, only certain setting fields are available. Fill in all fields marked with Must be defined or with a red *. Other fields can be left empty, unless your service provider has instructed otherwise. To use a data connection, your service provider must support this feature, and if necessary, activate it for your SIM card. Create access point groups Press and select Tools > Settings > Connection > Destinations. Some applications allow you to use access point groups to connect to a network. To avoid selecting which access point to use every time the device attempts to connect to a network, you can create a group that contains various access points, and define the order in which the access points are used to connect to a network. For example, you can add wireless LAN (WLAN) and packet data access points to an internet access point group and use the group for browsing the web. If you give the WLAN access point the higher priority, the device connects to the internet through a WLAN if available and through a packet data connection if not. To create a new access point group, select Options > Manage > New destination. To add access points to an access point group, select the group and Options > New access point. To copy an existing access point from another group, select the group, scroll to an existing access point, and select Options > Organise > Copy to other dest.. CI) H 01 C E w N To change the priority order of access points within a group, scroll to an access point, and select Options > Organise > Change priority. Packet data access points SelectMenu > Ctrl. panel > SettingsandConnection > Destinations > Access point, and follow the instructions on the display. Or, open one of the access point groups, and select an access point marked with #. Use the instructions provided by your service provider to edit the following: Access point name — The access point name is provided by your service provider. User name — The user name may be needed to make a data connection, and is usually provided by your service provider. Prompt password — If you want to set the device to ask for a password every time you log in to a server, or if you do not want to save your password in the device, select Yes. Password — A password may be needed to make a data connection and is usually provided by your service provider. Authentication — Select Secure to always send your password encrypted or Normal to send your password encrypted when possible. Homepage — Depending on the access point type you are setting up, enter the web address or the address of the multimedia message centre. Use access point — Select After confirmation to set the device to ask for confirmation before the connection using this access point is created, or Automatically to set the device to connect to the destination using this access point automatically. Select Options > Advanced settings and from the following: Network type — Select the internet protocol type to transfer data to and from your device. The other settings depend on the selected network type. Phone lPaddress (for IPv4 only) — Enterthe IP address of your device. DNS addresses — Enterthe IP addresses of the primary and secondary DNS servers, if required by your service provider. To obtain these addresses, contact your internet service provider. Proxy server address — Enterthe address ofthe proxy server. Proxy port number — Enter the port number of the proxy server. WLAN internet access points SelectMenu > Ctrl. panel > Settings and Connection > Destinations > Access point, and follow the instructions on the display. Or, open one of the access point groups, select an access point marked with (x), and select Options > Edit. Use the instructions provided by your service provider to edit the following: WLAN network name — Select Enter manually or Search for networks. If you select an existing network, WLAN network mode and WLAN security mode are determined by the settings of its access point device. Network status — Define whether the network name is displayed. WLAN network mode — Select Ad-hoc to create an ad hoc network, and to allow devices to send and receive data directly; a WLAN access point device is not 119 120 H aT C E 4J N needed. In an ad hoc network, all devices must use the same WLAN network name. WLAN security mode — Select the encryption used: WEP, 802.1x, orWPA/WPA2. (802.1x and WPA/WPA2 are not available for ad hoc networks.) If you select Open network, no encryption is used. The WEP, 802.1x, and WPA functions can be used only if the network supports them. Use access point — Select After confirmation to set the device to ask for confirmation before the connection using this access point is created or Automatically to set the device to connect to the destination using this access point automatically. To enter the settings for the selected security mode, select WLAN security settings. Advanced WLAN settings Select Options > Advanced settings and from the following: IPv4 settings — Enter the IP address of your device, the subnet IP address, the default gateway, and the IP addresses of the primary and secondary DNS servers. Contact your internet service provider for these addresses. IPv6 settings — Define the type of DNS address. Ad-hoc channel (only for ad hoc networks) —To enter a channel number (1-11) manually, select User defined. Proxy server address — Enter the address for the proxy server. Proxy port number — Enter the proxy port number. Packet data (GPRS) settings Select Menu > Ctrl.panel > Settings and Connection > Packet data. Your device supports packet data connections, such as GPRS in the GSM network. When you are using your device in GSM and UMTS networks, it is possible to have multiple data connections active at the same time; access points can share a data connection, and data connections remain active, for example, during voice calls. To define the packet data settings, select Packet data connection and When available to register the device to the packet data network when you switch the device on in a supported network, or When needed to register the device to a packet data network only when an application or action attempts to establish a packet data connection. This setting affects all access points for packet data connections. To use the device as a packet data modem for your computer, select Access point, and enter the access point name provided by your service provider. To use a high-speed data connection, select High speed packet access > Enabled. WLAN settings Select Menu > Ctrl. panel > Settings and Connection > Wireless LAN. To have an indicator displayed when there is a wireless LAN (WLAN) available in your current location, select Show WLAN availability > Yes. To select the interval for your device to scan for available WLANs, and to update the indicator, select Scan for networks. This setting is not available unless you select Show WLAN availability > Yes. To set the device to test the Internet capability of the selected WLAN automatically, to ask for permission every time, or to never perform the connectivity test, select Internet connectivity test > Run automatically, every time, or Never run. If you select Run automatically or allow the test to be performed when the device asks for it, and the connectivity test is performed successfully, the access point is saved to internet destinations. To check the unique media access control (MAC) address that identifies your device, enter *#62209526# in the home screen. The MAC address is displayed. Aduanced WLAN settings Select Options > Advanced settings. The advanced WLAN settings are normally defined automatically, and changing them is not recommended. To edit the settings manually, select automatic configuration > Disabled, and define the following: Long retry limit — Enter the maximum number of transmission attempts if the device does not receive a receiving acknowledgement signal from the network. Short retry limit — Enter the maximum number of transmission attempts if the device does not receive a clear-to-send signal from the network. RTS threshold — Select the data packet size at which the WLAN access point device issues a request to send before sending the packet. TX power level — Select the power level of your device when sending data. Radio measuremer*, — Enable or disable the radio measurements. Power saving — Select whether to use the WLAN power saving mechanism to save the power in the device battery. Using the power saving mechanism enhances the battery performance but may weaken WLAN interoperability. To restore all settings to their original values, select options > Restore defaults. WEAN security settinac Select.denu > Ctrl. panel > Settings and ronnection > Destinations > Access point, and follow the instructions on the display. To edit a wireless LAN (WLAN) access point, open one of the access point groups, and select an access point marked with KA). To enter the settings for the selected security mode, select WLAN security settings. WEP security settings Select WEP as the WLAN security mode. The wired equivalent privacy (WEP) encryption method encrypts data before it is transmitted. Access to the network is denied to users who do not have the required WEP keys. When the WEP security mode is in use, and your device receives a data packet not encrypted with the WEP keys, the data is discarded. 121 a1 E GJ 122 iT In an ad-hoc network, all devices must use the same WEP key. Select WLAN security settings and from the following: WEP key in use — Select the desired WEP key. Authentication type — Select Open or Shared. WEP key settings — Edit the settings for the WEP key. WEP key settings In an ad-hoc network, all devices must use the same WEP key. Select WLAN security settings > WEP key settings and from the following: WEP encryption — Select the desired WEP encryption key length. WEP key format — Select whether you want to enter the WEP key data in ASCII or Hexadecimal format. WEP key — Enter the WEP key data. 802.1x security settings Select 802.1x as the WLAN security mode. ""' lx authenticates and authorises devices to access a wireless network, and prevents access if the authorisation process fails. Select WLAN security settin and from the following: WPA/WPA2 — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification). EAP plug-in settings — If you selected WPA/WPA2 > EAP, select which EAP plug-ins defined in your device to use with the access point. Pre-shared key —If you selected WPA/WPA2 > Pre-shared key, enter the shared private keythatidentifies your device to the WLAN to which you connect. WPA security settings Select WPA/WPA2 as the WLAN security mode. Select WLAN security settings and from the following: WPA/WPA2 — Select EAP (Extensible Authentication Protocol) or Pre-shared key (a secret key used for device identification). EAP plug-in settings — If you select WPA/WPA2 > EAP, select which EAP plug-ins defined in your device to use with the access point. Pre-shared key — If you select WPA/WPA2 > Pre-shared key, enter the shared private keythatidentifies your device to the WLAN to which you connect. WPA2 only mode — To allow both TKIP and AES (Advanced Encryption Standard) encryption, select Off. To allow AES only, select Wireless LAN plugins Select Menu > Ctrl. panel > Settings and Coni Destinations, and an access point group. The extensible authentication protocol (EAP) plug-ins are used in wireless networks to authenticate wireless devices and authentication servers, and the different EAP plug-ins make possible the use of various EAP methods (network service). You can view the EAP plug-ins currently installed in your device (network service). EAP plug-inc To define the EAP plug-in settings, select Options > New access poing and define an access point that uses WLAN as a data bearer. Select 802.1x or WPA/WPA2 as the security mode. Select WLAN security settings > WPA/WPA2 > EAP > EAP plug-in settings. Use EAP plug-ins To use an EAP plug-in when you connect to a WLAN using the access point, select the desired plug-in and Options > Enable. The EAP plug-ins enabled for use with this access point have a check mark next to them. To not use a plug-in, select Options > Disable. To edit the EAP plug-in settings, select Options > Edit. To change the priority of the EAP plug-in settings, select Options > Raise priority to attempt to use the plug-in before other plug-ins when connecting to the network with the access point, or Options > Lower priority to use this plug-in for network authentication after attempting to use other plug-ins. See the device help for more information on EAP plugins. Session initiation protocol (SIP) settings Select Menu > Ctrl. panel > Settingsand Connection > SIP settings. The session initiation protocol (SIP) is used for creating, modifying, and terminating certain types of communication sessions with one or more participants (network service). Typical communication sessions are video sharing and net calls. SIP profiles include settings for these sessions. The SIP profile used by default for a communication session is underlined. To create a SIP profile, select Options > New SIP profile > Use default profile or Use existing profile. To select the SIP profile you want to use by default for communication sessions, select Options > Default profile. Edit SIP profiles SelectMenu > Ctrl. panel > Settings and connection > "" settings. Select Options > Edit and from the following: Profile name — Enter a name for the SIP profile. Service profile — Select IETF or Nokia 3GPP. Default destination — Select the destination to use for the internet connection. Default access point — Select the access point to use for the internet connection. Public user name — Enter your user name provided by your service provider. Use compression — Select if compression is used. Registration — Select the registration mode. Use security — Select if security negotiation is used. Proxy server — Enter the proxy server settings for this SIP profile. Registrar server — Enter the registration server settings for this SIP profile. _C ~ d 123 Edit SIP proxy servers Select Options > New SIP profile or Edit > Proxy server. vl Proxy servers are intermediate servers between a browsing service and its users used by some service providers. These servers may provide additional security and speed up access to the service. Select from the following: Proxy server address — Enter the host name or IP address of the proxy server in use. Realm — Enter the proxy server realm. User name and Password — Enter your user name and password for the proxy server. Allow loose routing — Select if loose routing is allowed. Transport type — Select , or . Port — Enter the port number of the proxy server. Configuration settings SelectMenu > Ctrl. panel > Settings and Connection > Configurations. You can receive messages from your service provider or company information management containing configuration settings for trusted servers. These settings are automatically saved in Configurations. You may receive configuration settings for access points, multimedia, or e-mail services, and instant messaging (IM) or synchronisation settings from trusted servers. To delete configurations for a trusted server, select . The configuration settings for other applications provided by this server are also deleted. Restrict packet data Select Menu > Ctrl. panel > Settings and 7 ennfrn1 Edit registration servers Select Options > New SIP profile or Frdit > server. Select from the following: Registrar server address — Enter the host name or IP address of the registrar server in use. Realm — Enter the registrar server realm. User name and Password — Enteryour user name and password for the registrar server. Transport type — Select UDP, Automatic, or TCP. 124 • Port — Enter the port number of the registrar server. With the access point control service, you can restrict packet data connections from your device to certain access points only. Your SIM card may not support the access point control service. For more information, contact your service provider. To restrict packet data connections from your device, select Options > Activate restrictions. You need your PIN2 code to activate and deactivate access point control or to edit the packet data access points on the control list. To add access points that can be used for packet data connections to the control list, select Options > Add name manually. To enable connections to an operator-provided access point, create an empty access point. Select Menu > Ctrl. panel > Settings and Applications. Shortcuts Here are some of the available keyboard shortcuts in your device. Shortcuts can make the use of the applications more efficient. Ctrl +X Ctrl + A Home screen Cut text Select all. ueneral shortcuts Left selection key Lock and unlock the keypad and + right selection keyboard. Power key Press and hold to switch your device on and off. key Call key Open the call log. Press once to switch between profiles. 0 Press and hold to open your Sym key Press and hold to activate or deactivate Bluetooth connectivity. homepage in the Web browser. 1 Press and hold to call your voice Ctrl key Press and hold to activate or deactivate the Silent profile. mailbox. Ctrl + C i Copy text. :trl + V Paste text. vi .4n1 O u t O Z N 126 Number key (2­9) Call a phone number using speed dialling. You must first activate speed dialling in Menu > Ctrl. panel and Settings > Phone > Call > SpeE dialling. Web shortcuts * Zoom in the page. # Zoom out the page. 0 Go to the homepage. 1 Show the toolbar 2 Open the search dialog. 3 Return to the previous page. 4 Save the current page as a bookmark. 5 Open the map of keypad shortcuts. 6 Reload the current page. 7 View the page in full screen. 8 View the page overview. 9 Open the dialog for entering a new web address. E-mail R Create a reply message to the sender of the e-mail message. A Create a reply message to the sender and all other recipients. F Forward the e-mail message. N Open the next e-mail message. P Open the previous e-mail message. 0 Open the selected e-mail message. L Change the follow-up status of the message. J Move up one page in the e-mail message. K Move down one page in the e-mail message. T Move to the first e-mail message in the mailbox or move to the beginning of an e-mail message. B Move to the last e-mail message in the mailbox or move to the end of an e­mail message. M Open the list of e-mail folders for moving messages. U Change the read or unread status of an e-mail message. E Accept a meeting request. G Tentatively accepta meeting request. Create a new e-mail message. Remove the selected e-mail messages. ( D D Open the day view. W Open the week view. M Open the month view. T Open the to-do view. N Add a new meeting. V Decline a meeting request. W Sort e-mail messages. I Expand and collapse the messages. Z Start the synchronisation. S Start the search. Calendar shortcuts for keyboard IA ¡Open the agenda view. Glossary Glossary 3G 3rd generation mobile communications. A digital system for mobile communications which aims at global use and provides increased bandwidth. 3G lets a mobile device user access a wide variety of services, such as multimedia. Ad-hoc A WLAN network mode where two or operating more devices connect to each other using mode WLAN directly without a WLAN access point. Cookies Cookies are little pieces of information, given by the server to you, to store information about your visits to a web site. When you accept cookies, the server is able to evaluate your use of the web site, what you are interested in, what you want to read, and so on. DNS Domain name service. An internet service that translates domain names such as www.nokia.com into IP addresses such as 192.100.124.195. Domain names are easier to remember but this translation is needed because the internet is based on IP addresses. 127 Extensible authentication protocol. EAP plug-ins are used in wireless networks to authenticate wireless devices and authentication servers. Enhanced GPRS. EGPRS is similar to GPRS, but it enables faster connection. For availability and data transfer speed, contact your service provider. General packet radio service. GPRS enables wireless access for mobile phones to data networks (network service). GPRS uses packet data technology where information is sent in short bursts of data over the mobile network. The benefit of sending data in packets is that the network is occupied only when sending or receiving data. As GPRS uses the network efficiently, it allows for quick data connection setup and fast data transmission speeds. You must subscribe to the GPRS service. For availability and subscription to GPRS, contact your service provider. During a voice call, you cannot establish a GPRS connection, and any existing GPRS connection is put on hold unless the network supports dual transfer mode. GPS High-speed downlink packet access. HSDPA brings high-speed data delivery to 3G terminals, ensuring that users requiring effective multimedia capabilities benefit from data rates previously unavailable because of limitations in the radio access network. Hypertext transfer protocol. A document transfer protocol used in the web. HTTP over a secure connection. Internet mail access protocol, version 4. A protocol used for accessing your remote mailbox. Internet access point An access point is where your device connects to a network. To use e-mail and multimedia services or to connect to the internet and browse web pages, you must first define internet access points for these services. Infrastructure operating mode A WLAN network mode where devices are connected to WLAN using a WLAN access point. EAP EGPRS GPRS 128 DTMF tones Dual-tone multifrequency tones. The DTMF system is used by touch-tone telephones. DTMF assigns a specific frequency, or tone, to each key so that it can easily be identified by a microprocessor. DTMF tones allow you to communicate with voice mailboxes, computerised telephony systems, and so HSDPA on. Global positioning system. GPS is a worldwide radio navigation system. HTTP HTTPS IMAP4 Universal Mobile Telecommunications System. UMTS is a 3G mobile communication system. Besides voice and data, UMTS enables audio and video delivery to wireless devices. When you use your device in GSM and UMTS networks, multiple data connections can be active at the same time, and access points can share a data connection. In the UMTS network, data connections remain active during voice calls. You can, for example, browse the web faster than previously possible while simultaneously speaking on the phone. PIN Personal identity number. The PIN code UMTS protects your device from unauthorised use. The PIN code is supplied with the SIM card. If the PIN code request is selected, the code is required each time the device is switched on. The PIN code must be 4 to 8 digits long. PIN? The PIN? code is supplied with some SIM cards. The PIN? code is required to access certain functions supported by the SIM card. The length of the PIN? code is 4 to 8 digits. POP3 Post office protocol, version 3. A common mail protocol that can be used for accessing your remote mailbox. PUK and PUK2 Personal Unblocking Key. PUK and PUK2 codes are required to change a blocked PIN code or PIN2 code, respectively. The length of the code is 8 digits. SIP Session Initiation Protocol. SIP is used for creating, modifying, and terminating certain types of communication sessions with one or more participants. SSID Service set identifier. SSID is the name that identifies the specific WIAN. Streaming Streaming audio and video files means playing them directly from the web without downloading them first to your device. PIN code used in UMTS network. UPUK UPIN Unblocking Key. UPUK code is required to change a blocked UPIN code or PIN2 code. The length of the code is 8 digits. SIM card used in UMTS network. USSD command A service request, such as request to activate an application or configure various settings remotely, that you can send to your operator or service provider with your device. Voice over IP technology. VoIP is a set of protocols that facilitate phone calls over an IP network, such as the internet. UPIN USIM VoIP 129 Troubleshooting VPN Virtual private network. VPN creates a secure connection to compatible corporate intranet and services, such as e-mail. WAP Wireless application protocol. WAP is an international standard for wireless communication. WEP Wired equivalent privacy. WEP is an encryption method that encrypts data before it is transmitted in WLAN. WLAN Wireless local area network. WPA Wi-Fi Protected Access. Security method for WLAN. WPA2 Wi-Fi Protected Access 2. Security method for WLAN. 130 Troubleshooting To view frequently asked questions about your device, go to www.nokia.com/support. Q: What is my lock, PIN, or PUK code? A: The default lock code is 12345. If you forget or lose the lock code, contact your device dealer. If you forget or lose a PIN or PUK code, or if you have not received such a code, contact your network service provider. Q: How do I close an application that is not responding? A: Press and hold the home key. Scroll to the application, and press the backspace key to close the application. Q: Why do images look smudgy? A: Ensure that the camera lens protection windows are clean. Q: Why do missing, discoloured, or bright dots appear on the screen every time I switch on my device? A: This is a characteristic of this type of display. Some displays may contain pixels or dots that remain on or off. This is normal, not a fault. Q: Why can't I find my friend's device while using Bluetooth connectivity? A: Check that both devices are compatible, have activated Bluetooth connectivity, and are not in hidden mode. Check also that the distance between the two devices is not over Troubleshooting 10 metres (33 feet) and that there are no walls or other obstructions between the devices. Q: Why can't I close a Bluetooth connection? A: If another device is connected to your device, you can close the connection using the other device or by deactivating Bluetooth connectivity. Select Menu > Ctrl panel > Connectivity > Bluetooth and Bluet-°"- > Off. Q: Why can't I see a wireless LAN (WIAN) access point even though I know I'm within its range? A: Check that the Offline profile is not in use in your device. The WLAN access point may use a hidden service set identifier (SSID). You can only access networks that use a hidden SSID if you know the correct SSID, and have created a WLAN access point for the network on your Nokia device. Check that the WLAN access pointis not on channels 12-13, as they cannot be associated with. Q: How do I turn the WLAN off on my Nokia device? A: The WLAN on your Nokia device deactivates when you are not connected or trying to connect to another access point, or not scanning for available networks. To further reduce battery consumption, you can specify that your Nokia device does not scan, or scans less often, for available networks in the background. The WLAN deactivates in between background scans. To stop the background scans, select Menu > Ctrl. panel > Settings and Connection > Wireless LAN > Show WLAN availability > Never. You can still manually scan for available WLANs and connect to WIANs as usual. To increase the background scan interval, select WLAN availabilit! > , and define the interval in for networks. Q: Why can't I browse the web even though the WLAN connection is working and the IP settings are correct? A: Check that you have defined the HTTP/ HTTPS proxy settings correctly in the advanced settings of your WIAN access point. Q: How do I check the signal quality of my WLAN connection? — Select Menu > Ctrl. panel > Connectivity > Conn. mgr. and Active connections > Options > Details. If the signal quality is weak or moderate, you may encounter connection problems. Try again closer to the access point. Q: Why do I have problems with the security mode? A: Check that you have configured the security mode correctly, and that it is the same that the network uses. To check the security mode the network uses, select Menu > Ctrl. panel > Connectivity > Conn. mgr. and Active data connections > Options > Details. Check also the following: you have the correct WPA mode (preshared key or EAP), you have disabled all EAP types that are not needed, and all the EAP type settings are correct (passwords, user names, certificates). Q: Why can't I select a contact for my message? A: The contact card does not have a phone number, an address, or an e-mail address. Select Menu > Contacts, and edit the contact card. 131 Q: The note Retrieving message is shown briefly. What is happening? A: The device is trying to retrieve a multimedia message from the multimedia messaging centre. This note is shown if you have selected Menu > Messaging and Options > Settings > Multimedia message > Multimedia retrieval > Always automatic. Check that the settings for multimedia messaging are defined correctly and that there are no mistakes in phone numbers or addresses. Q: How can I end the data connection when the device starts a data connection again and again? A: The device may be trying to retrieve a multimedia message from the multimedia message centre. To stop the device from making a data connection, select Menu > Messaging and Options > Settings > Multimedia message > Multimedia retrieval > Manual to have the multimedia messaging centre save messages to be retrieved later, or Off to ignore all incoming multimedia messages. If you select Manual, you receive a notification when there is a new multimedia message that you can retrieve in the multimedia message centre. If you select Off, the device does not make any network connections related to multimedia messaging. To set the device to use a packet data connection only if you start an application or action that needs it, select Menu > Ctrl. panel > Settings and Connection > Packet data > Packet data connection > When needed. If this does not help, restart the device. Q: How do I save battery power? A: Many features in your device increase the demand on battery power and reduce the battery life time. To save battery power, do the following: Deactivate Bluetooth connectivity when you do not need it. Stop the background scans for WLAN. Select Menu > Ctrl. panel > Settings and Connection > Wireless LAN > ShowWLAN availability > Never.You can still manually scan for available WLANs and connect to WLANs as usual. Set the device to use a packet data connection only if you start an application or action that needs it. Select Menu > Ctrl. panel > Settings and Connection > Packet data > Packet data connection > When needed. Prevent the device from automatically downloading new maps in the Maps application. Select Menu > Maps and Options > Settings > Internet > Connection. Change the time-out after which the backlight is switched off. Select Menu > Ctrl. panel > Settings and General > Personalisation > Display > Light time-out. Close the applications you are not using. Press and hold the home key. Scroll to the application, and press the backspace key to close the application. 132 Green tips (;) we: Save energy You do not need to charge your battery so often if you do the following (if available for your device): Close applications and data connections, for example, your Bluetooth connection, when not in use. Decrease the brightness of the screen. Set your device to enter power saver mode after the minimum period of inactivity, if available in your device. Deactivate unnecessary sounds, such as key tones. Recycle All materials of this device can be recovered as materials and energy. For information on how to recycle your old Nokia products, go to www.nokia.com/werecycle, or using a mobile device, nokia.mobi/werecycle. Recycle packaging and user guides at your local recycling scheme. The crossed-out wheeled-bin symbol on your \, product, battery, literature, or packaging reminds you that all electrical and electronic products, batteries, and accumulators must be taken to separate collection at the end of their working life. This requirement applies in the European Union. Do not dispose of these products as unsorted municipal waste. For more information on the environmental attributes of your device, see www.nokia.com/ecodeclaration. Product and safety information Accessories °Warning: Use only batteries, chargers, and accessories approved by Nokia for use with this particular model. The use of any other types may invalidate any approval or warranty, and may be dangerous. In particular, use of unapproved chargers or batteries may present a risk of fire, explosion, leakage, or other hazard. 133 Product and safety information For availability of approved accessories, please check with your dealer. When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord. Proper charging. Unplug the charger from the electrical plug and the device when not in use. Do not leave a fully charged battery connected to a charger, since overcharging may shorten its lifetime. If left unused, a fully charged battery will lose its charge over time. Avoid extreme temperatures. Always try to keep the battery between 15°C and 25°C (59°F and 77°F). Extreme temperatures reduce the capacity and lifetime of the battery. A device with a hot or cold battery may not work temporarily. Battery performance is particularly limited in temperatures well below freezing. Do not short-circuit. Accidental short-circuiting can occur when a metallic object such as a coin, clip, or pen causes direct connection of the positive (+) and negative (-) terminals of the battery. (These look like metal strips on the battery.) This might happen, for example, when you carry a spare battery in your pocket or purse. Short-circuiting the terminals may damage the battery or the connecting object. Disposal. Do not dispose of batteries in a fire as they may explode. Dispose of batteries according to local regulations. Please recycle when possible. Do not dispose as household waste. Leak. Do not dismantle, cut, open, crush, bend, puncture, or shred cells or batteries. In the event of a battery leak, prevent battery liquid contact with skin or eyes. If this happens, flush the affected areas immediately with water, or seek medical help. Damage. Do not modify, remanufacture, attempt to insert foreign objects into the battery, or immerse or expose it to water or other liquids. Batteries may explode if damaged. Battery Battery and charger information Your device is powered by a rechargeable battery. The battery intended for use with this device is BP-4L. Nokia may make additional battery models available for this device. This device is intended for use when supplied with power from the following chargers: AC-8, AC-10. The exact charger model number may vary depending on the type of plug. The plug variant is identified by one of the following: E, EB, X, AR, U, A, C, K, or UB. The battery can be charged and discharged hundreds of times, but it will eventually wear out. When the talk and standby times are noticeably shorter than normal, replace the battery. Use only Nokia approved batteries, and recharge your battery only with Nokia approved chargers designated for this device. If a battery is being used for the first time or if the battery has not been used for a prolonged period, it may be necessary to connect the charger, then disconnect and reconnect it to begin charging the battery. If the battery is completely discharged, it may take several minutes before the charging indicator appears on the display or before any calls can be made. 134 Safe removal. Always switch the device off and disconnect the charger before removing the battery. Correct use. Use the battery only for its intended purpose. Improper battery use may result in a fire, explosion, or other hazard. If the device or battery is dropped, especially on a hard surface, and you believe the battery has been damaged, take it to a service centre for inspection before continuing to use it. Never use any charger or batterythat is damaged. Keep your battery out of the reach of small children. Nokia battery authentication guidelinoc Always use original Nokia batteries for your safety. To check that you are getting an original Nokia battery, purchase it from a Nokia authorised service centre or dealer, and inspectthe hologram label using the following steps: Authenticate hologram 1. When you look atthe hologram on the label, you should see the Nokia connecting hands symbol from one angle and the Nokia Original Enhancements logo when looking from another angle. 2. When you angle the hologram left, right, down and up, you should see 1, 2, 3 and 4 dots on each side respectively. Successful completion of the steps is not a total assurance of the authenticity of the battery. If you cannot confirm authenticity or if you have any reason to believe that your Nokia battery with the hologram on the label is not an authentic Nokia battery, you should refrain from using it, and take it to the nearest Nokia authorised service centre or dealer for assistance. To find out more about original Nokia batteries, see www.nokia.com/battery. axing care or your device Your device is a product of superior design and craftsmanship and should be treated with care. The following suggestions will help you protect your warranty coverage. Keep the device dry. Precipitation, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet, remove the battery, and allow the device to dry completely before replacing it. Do not use or store the device in dusty, dirty areas. Its moving parts and electronic components can be damaged. 41:01k...;LA Product and safety information 135 136 Product and safety information Do not store the device in high or cold temperature. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics. When the device warms to its normal temperature from a cold temperature, moisture can form inside the device and damage electronic circuit boards. Do not attempt to open the device other than as instructed in this guide. Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device. Only use a soft, clean, dry cloth to clean the surface of the device. Do not paint the device. Paint can clog the moving parts and prevent proper operation. Use only the supplied or an approved replacement antenna. Unauthorised antennas, modifications, or attachments could damage the device and may violate regulations governing radio devices. Use chargers indoors. Backup all data you want to keep, such as contacts and calendar notes. To reset the device from time to time for optimum performance, power off the device and remove the battery. These suggestions apply equally to your device, battery, charger, or any accessory. Recycl Always return your used electronic products, batteries, and packaging materials to dedicated collection points. This way you help prevent uncontrolled waste disposal and promote the recycling of materials. Check product environmental information and how to recycle your Nokia products at www.nokia.com/werecycle, or nokia.mobi/ werecycle. Aaaitionai satety information The surface of this device is nickel-free. Small children Your device and its accessories are not toys. They may contain small parts. Keep them out of the reach of small children. Operating environment. This device meets RF exposure guidelines in the normal use position at the ear or at least 2.2 centimetres (7/8 inch) away from the body. Any carry case, belt clip, or holder for body-worn operation should not contain metal and should position the device the above-stated distance from your body. To send data files or messages requires a quality connection to the network. Data files or messages may be Product and safety information delayed until such a connection is available. Follow the separation distance instructions until the transmission is completed. Parts of the device are magnetic. Metallic materials may be attracted to the device. Do not place credit cards or other magnetic storage media near the device, because information stored on them may be erased. Medical devices Operation of radio transmitting equipment, including wireless phones, may interfere with the function of inadequately protected medical devices. Consult a physician or the manufacturer of the medical device to determine whether they are adequately shielded from external RF energy. Switch off your device when regulations posted instruct you to do so. Hospitals or health care facilities may use equipment sensitive to external RF energy. Implanted medical device Manufacturers of medical devices recommend a minimum separation of 15.3 centimetres (6 inches) between a wireless device and an implanted medical device, such as a pacemaker or implanted cardioverter defibrillator, to avoid potential interference with the medical device. Persons who have such devices should: Always keep the wireless device more than 15.3 centimetres (6 inches) from the medical device. Not carry the wireless device in a breast pocket. Hold the wireless device to the ear opposite the medical device. Turn the wireless device off if there is any reason to suspect that interference is taking place. Follow the manufacturer directions for the implanted medical device. If you have any questions about using your wireless device with an implanted medical device, consult your health care provider. ~ieanny alas Some digital wireless devices may interfere with some hearing aids. Vehicles RF signals may affect improperly installed or inadequately shielded electronic systems in motor vehicles such as electronic fuel injection, electronic antilock braking, electronic speed control, and air bag systems. For more information, check with the manufacturer of your vehicle or its equipment. Only qualified personnel should service the device or install the device in a vehicle. Faulty installation or service may be dangerous and may invalidate your warranty. Check regularly that all wireless device equipment in your vehicle is mounted and operating properly. Do not store or carry flammable liquids, gases, or explosive materials in the same compartment as the device, its parts, or accessories. Remember that air bags inflate with great force. Do not place your device or accessories in the air bag deployment area. Switch off your device before boarding an aircraft. The use of wireless teledevices in an aircraft may be dangerous to 137 the operation of the aircraft and may be illegal. Product and safety information Potentially explosive environments Switch off your device in any area with a potentially explosive atmosphere. Obey all posted instructions. Sparks in such areas could cause an explosion or fire resulting in bodily injury or death. Switch off the device at refuelling points such as near gas pumps at service stations. Observe restrictions in fuel depots, storage, and distribution areas; chemical plants; or where blasting operations are in progress. Areas with a potentially explosive atmosphere are often, but not always, clearly marked. They include areas where you would be advised to turn off your vehicle engine, below deck on boats, chemical transfer or storage facilities and where the air contains chemicals or particles such as grain, dust, or metal powders. You should check with the manufacturers of vehicles using liquefied petroleum gas (such as propane or butane) to determine if this device can be safely used in their vicinity. To make an emergency call: If the device is not on, switch it on. Check for adequate signal strength. Depending on your device, you may also need to complete the following: Insert a SIM card if your device uses one. • Remove certain call restrictions you have activated in your device. Change your profile from Offline or Flight profile to an active profile. Press the end key as many times as needed to clear the display and ready the device for calls. Enter the official emergency number for your present location. Emergency numbers vary by location. Press the call key. When making an emergency call, give all the necessary information as accurately as possible. Your wireless device may be the only means of communication at the scene of an accident. Do not end the call until given permission to do so. Certification information (SAR) This mobile device meets guidelines for exposure to radio waves. Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organisation ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health. Emernanry rallc Important: This device operates using radio signals, wireless networks, landline networks, and user-programmed functions. If your device supports voice calls over the internet (internet calls), activate both the internet calls and the cellular phone. The device may attempt to make emergency calls over both the cellular networks and through your internet call provider if both are activated. Connections in all conditions cannot be guaranteed. You 138 should never rely solely on any wireless device for essential communications like medical emergencies. Product and safety information The exposure guidelines for mobile devices employ a unit of measurement known as the Specific Absorption Rate or SAR. The SAR limit stated in the ICNIRP guidelines is 2.0 watts/kilogram (W/kg) averaged over 10 grams of tissue. Tests for SAR are conducted using standard operating positions with the device transmitting at its highest certified power level in all tested frequency bands. The actual SAR level of an operating device can be below the maximum value because the device is designed to use only the power required to reach the network. That amount changes depending on a number of factors such as how close you are to a network base station. The highest SAR value under the ICNIRP guidelines for use of the device at the ear is 1.31 W/kg. Use of device accessories may result in different SAR values. SAR values may vary depending on national reporting and testing requirements and the network band. Additional SAR information may be provided under product information at www.nokia.com. 139 ti__Index Symbols/Numbers 3-D ringing tones 84 802.1x security settings 122 A-GPS (assisted GPS) 68 access codes 12 access points 52,118 groups 118 VPN 111 accessories settings 114 active notes 63 settings 63 active toolbar in Photos 90 albums media 90 alert tones 113 answering calls 30 antennas 16 application manager 107 application settings 125 applications 107 assisted GPS (A-GPS) 68 attachments multimedia messages 46 140 audio files details 98 audio messages 43 audio themes 83 autolock period 115 background image 83 backing up device memory 64 battery charging 16 inserting 14 saving power 13 blogs 60 Bluetooth 54, 55 Bluetooth connectivity blocking devices 56 device visibility 54 low memory 56 pairing devices 55 receiving data 56 security 54 settings 54 turning on/off 54 bookmarks 60 browser 61 bookmarks 58, 60 browsing pages 58, 59 cache memory 60 searching content 60 security 61 settings 61 toolbar 59 cable connection 57 cache memory 60 calculator 63 calendar 25 creating entries 25 meeting requests 25 views 26 calendar key 24 call barring 32 call divert 31 call log 37 call waiting 31 caller ID 116 calls 29 answering 30 conference 30 dialled 37 duration of 37 missed 37 options 29 received 37 rejecting 30 restricting See fixed dialling settings 116 voice mail 30 X as ß C 1-1 camera capturing images 84 image settings 86 playing videos 86 scenes 85 sequence mode 85 toolbar 84 video clips 86 video settings 87 viewing images 86 cell broadcast 46 settings 48 certificates details 105 settings 105 charging the battery 16 chat services (IM) 49 computer connections 57 See also data connections conference calls 30 configuration messages 124 connectors 17 contacts 26, 27 adding ringing tones 27 copying 19 groups 27 searching 27 settings 28 synchronising 53,110 contacts key 24 content synchronising, sending, and retrieving 20 converting currencies 65 measurements 65 cookies 61 currency conversions 65 data cable 57 data connections PC connectivity 57 synchronisation 53,110 wireless 51 date settings 114 declining calls 30 decrypting device memory and memory card 104 device manager 106 dialled numbers 37 dictionary 67 dismissing calls 30 display settings 112 DLNA 57 duration of calls 37 e-mail accounts 41 adding attachments 40 attachments 40 deleting 41 disconnecting 41 folders 41 out-of-office reply 42 reading 40 searching 41 sending 40 settings 42 setup 39 e-mail key 24 e-mail key settings 115 EAP plug-in settings 123 using an EAP plug-in 123 encrypting device memory and memory card 103 equaliser 97 feeds, news 60 file management 64 file manager 64 files flash files 99 fixed dialling 104 flashlight 28 FM radio 99 gallery 87 presentations 88 sound clips 88 streaming links 88 general information 10 GPRS settings 120 141 GPS position requests 70 GPS (Global Positioning System) 68 GPS (global positioning system) 68 headset 18 help application 11 home key 24 home screen 22, 23 settings 82 IAPs (internet access points) 52 IM (instant messaging) 49 images editing 91 printing 92 installing applications 107 Internet browser 58 Internet calls 116 Internet connection 58 See also browser Internet radio 100 favourites 101 searching for stations 101 settings 102 station directory 101 M; CI 11= C 1-1 142 Java applications 107 JME Java application support 107 key store 106 keypad lock settings 115 tones 113 keys 17 WEP keys 122 landmarks 70 language settings 113 licences 109 location information 68 lock code 12, 16, 102, 115 locking device 102 device autolock 115 keypad 115 logos welcome logo 112 Maps 72 browsing 72 changing views 73 display elements 73, 78 downloading maps 73 driving routes 77 Favourites 76 finding locations 74 navigating 77, 79 organising places 76 organising routes 76 planning routes 79 positioning 74 saving places 75 saving routes 75 sending places 76 sharing locations 77 shortcuts 80 synchronising 76 traffic information 78 viewing location details 75 voice guidance 77 walking routes 79 maps compass 73 measurements converting 65 media radio 99 meeting requests receiving 41 memory clearing 13 web cache 60 memory card 15 locking 103 passwords 103 message reader 42 messages 38 cell broadcast settings 48 configuration messages 124 service messages 46 settings 49 speech options 42 text message settings 47 messaging folders 38, 39 Mini Map 59 MMS (multimedia message service) 43, 47 multimedia 87 multimedia messages 43, 47 attachments 46 creating presentations 45 receiving 44 replying to 44 multitasking 28 music player playing 96 playlists 96 navigation tools 68 network settings 117 network settings 50 news feeds 60 Nokia Ovi Player 97 Nokia support information 10 notes 67 Office Communicator 49 One-touch keys 113 operator selecting 117 Optical Navi key 24 original settings 115 out-of-office reply message 42 Ovi 28 Ovi by Nokia 21 Ovi Files 28 Ovi Music 97 Ovi Store 21 Ovi Suite 20 packet data restricting 124 settings 120 packet data connection access point settings 119 counters 37 page overview 59 PDF reader 65 personalisation changing language 113 display 112 tones 113 personalising your device 81 photos editing 91 file details 89 organising files 89 red-eye 91 tags 90 toolbar 90 viewing 89 PictBridge 92 pictures copying 19 PIN code 12 changing 115 pin code 16 PIN2 code 12 playing video and audio 98 positioning settings 115 positioning information 68 positioning settings 71 predictive text input 113 presentations 45, 88 printer settings 66 printing 66 images 92 profiles creating 81 personalising 81, 82 selecting ringing tones 82 proxy settings 119 PUK codes 12 radio 99 settings 100 stations 100 RealPlayer playing media clips 98 settings 98 viewing clip details 98 red-eye removal 91 rejecting calls 30 remote configuration 106 remote database search 27 remote lock 102 143 X a ß c 1-1 remote SIM mode 56 restoring original settings 115 ringing tones 113 3-D 84 contacts 27 in profiles 82 vibrating alert 113 roaming 50 screen saver 83,112 scroll key 113 searching contacts 27 security browser 61 device and SIM card 115 memory card 103 security code 12,102 security module 106 sensor settings 25,114 service commands 46 service messages 46 settings 48 settings access points 118 accessories 114 active notes 63 advanced WLAN 121 applications 125 Bluetooth connectivity 54 browser 61 call 116 144 camera 86 cell broadcast 48 certificate 105 contacts 28 date 114 display 112 e-mail key 115 EAP plug-ins 123 FM radio 100 GPRS 120 internet radio 102 keypad lock 115 language 113 lights 113 messages 47 network 50,117 packet data 120 packet data access points 119 positioning 71, 115 printer 66 RealPlayer 98 restoring 115 security 114 sensor settings 114 service messages 48 SIP 123 text messages 47 time 114 tones 113 video sharing 35 WEP security 121 WLAN 53, 119,120 WLAN internet access points 119 WLAN security 121 Share online 93 account settings 95 accounts 93 activating services 93 advanced settings 95 creating posts 94 data counters 96 one-click upload 94 Outbox 94 posting 94 service content 95 service provider settings 95 subscribing 93 tags 94 shared video 34 sharing media files online 93 shortcuts 80,125 SIM card inserting 14 text messages 44 SIP creating profiles 123 editing profiles 123 editing proxy servers 124 editing registration servers 124 settings 123 slide show 91 SMS (short message service) 43 software updating 10 software applications 107 software updates 10,11 sound clips 88 speech 42 speed dialling 31 streaming links 88 support 10 X GJ ß C 1-1 Symbian applications 107 synchronisation of data 53,110 text changing size 112 writing 18 text messages messages on SIM card 44 sending 43 settings 47 themes 83 audio 83 downloading 83 time settings 114 tones 113 settings 113 transferring content 19 transferring music 97 troubleshooting 130 updates 11 applications 10 device software 10 UPIN code 12 changing 115 uploading media files 93 UPUK code 12 USB data cable 57 useful information 10 vibrating alert 113 video playing 86 video calls 33, 34 options during 34 video clips details 98 playing 98 shared 34 video sharing accepting invitation 36 sharing live video 35 sharing video clips 35 videos copying 19 virtual private network use in applications 111 voice calls See calls voice commands 32 voice mail calling 30 changing number 30 VPN access points 111 use in applications 111 warning tones 113 web browser 58 web connection 58 welcome note 112 WEP keys 122 security settings 121 wireless LAN (WLAN) 51 MAN 802.1x security settings 122 advanced settings 121 MAC address 53,120 security settings 121 settings 53,120 WEP keys 122 WPA security settings 122 WLAN (wireless local area network) 51 WPA security settings 122 wrist strap 18 writing 18 Zip manager 65 145